1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
37-610 Code 125 Help
Guest
Unregistered
 
#1

08-30-2006, 04:15 PM
Hello,

Since I am very new to the Philco Phorum, I want to say right off the bat, that I have enjoyed reading through the posts and seeing how muich knowledge is out there concerning the restoration of these great radios. I do have several questions about where to get information and schematics for a radio that I recently purchesed.

I obtained the radio via EBay a while back and I am finally getting around to restoring it. It was sold to me as a 37-61 but as I have cleaned it up and gotten a better look at it I have found out that it is a 37-610 code 125. The first question I have is: What does code 125 mean? Also, where can I get the schematics for a 37-610 code 125? All of the ones I have been able to find are for a code 121/122 and they don't match the electronics that are in my radio. Can anybody help?

Thanks in advance,

O3-UV
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
37-610 Code 125 Help - by Guest - 08-30-2006, 04:15 PM
[No subject] - by Chuck Schwark - 08-30-2006, 05:07 PM
[No subject] - by Guest - 09-01-2006, 11:07 AM
[No subject] - by Guest - 09-13-2006, 02:18 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 1470 online users. [Complete List]
» 3 Member(s) | 1467 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration