1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 71 restoration
Keith
Senior Member
****
Posts: 336
Threads: 50
Joined: Apr 2011
City: Orrville State, Province, Country: Ohio
#2

09-29-2011, 01:36 AM
Does this metal can cap look original or is it a replacment for a bad cap in one of the bakelite blocks?

It only has one wire coming out and it soldered to the leg of the 13k 3watt resistor thats on the cathode of the 36 tube. Also its not listed on the parts list or in the parts diagram.

[Image: http://i1129.photobucket.com/albums/m501...AG0702.jpg]

Its installed here:
[Image: http://i1129.photobucket.com/albums/m501...cation.jpg]

According to Philcorepairbench it is a .5mfd which could replace one of the .5's in the bakelite block 3615-AF (5 on the parts list).

I tried to attached the service bulletin for this radio but no go. Not sure what up with that.
-Keith
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco 71 restoration - by Keith - 09-29-2011, 12:48 AM
RE: Philco 71 restoration - by Keith - 03-02-2012, 06:09 PM
Re: Man this thing is a nightmare - by Keith - 09-29-2011, 01:36 AM
Re: Man this thing is a nightmare - by Keith - 09-29-2011, 10:14 PM
Re: Man this thing is a nightmare - by Keith - 10-06-2011, 12:29 AM
Re: Man this thing is a nightmare - by Arran - 10-06-2011, 02:24 AM
Re: Man this thing is a nightmare - by rghines1 - 10-06-2011, 10:20 AM
Re: Man this thing is a nightmare - by exray - 10-06-2011, 12:41 PM
Re: Man this thing is a nightmare - by Keith - 10-08-2011, 10:34 PM
Re: Man this thing is a nightmare - by Marsupial - 10-08-2011, 11:52 PM
Re: Man this thing is a nightmare - by exray - 10-09-2011, 05:56 AM
Re: Man this thing is a nightmare - by Keith - 10-10-2011, 01:40 PM
Re: Philco 71 restoration - by Keith - 10-31-2011, 05:10 PM
Re: Philco 71 restoration - by 7estatdef - 10-31-2011, 08:48 PM
Re: Philco 71 restoration - by 7estatdef - 10-31-2011, 09:00 PM
Re: Philco 71 restoration - by Keith - 11-01-2011, 01:03 AM
Re: Philco 71 restoration - by Keith - 11-01-2011, 01:06 AM
Re: Philco 71 restoration - by 7estatdef - 11-01-2011, 10:58 PM
Re: Philco 71 restoration - by Keith - 11-03-2011, 01:03 AM
Re: Philco 71 restoration - by 7estatdef - 11-03-2011, 02:59 AM
Re: Philco 71 restoration - by codefox1 - 11-03-2011, 10:04 AM
Re: Philco 71 restoration - by Keith - 11-03-2011, 06:00 PM
Re: Philco 71 restoration - by 7estatdef - 11-03-2011, 06:26 PM
Re: Philco 71 restoration - by Keith - 11-03-2011, 06:31 PM
Re: Philco 71 restoration - by 7estatdef - 11-03-2011, 06:42 PM
Re: Philco 71 restoration - by Keith - 11-03-2011, 07:40 PM
Re: Philco 71 restoration - by 7estatdef - 11-03-2011, 08:39 PM
Re: Philco 71 restoration - by Keith - 11-03-2011, 09:38 PM
Re: Philco 71 restoration - by Keith - 11-04-2011, 12:29 AM
Re: Philco 71 restoration - by Keith - 11-04-2011, 02:33 PM
Re: Philco 71 restoration - by Keith - 11-30-2011, 11:56 PM
Re: Philco 71 restoration - by TA Forbes - 12-01-2011, 12:37 AM
Re: Philco 71 restoration - by TA Forbes - 12-02-2011, 09:54 PM
Re: Philco 71 restoration - by codefox1 - 12-03-2011, 11:48 AM
Re: Philco 71 restoration - by Keith - 12-04-2011, 03:03 PM
Re: Philco 71 restoration - by Keith - 12-23-2011, 04:36 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 38-7: what caps & resistors do fail typically?
Since you stated earlier, you have a console 38-7XX.  They also had a 38-7T (table), and 38-7CS (chairside).  A very nic...GarySP — 01:18 PM
Part numbers to model cross
That I wouldn't know, but sometimes the radio document itself shows one, same as the capacitor cans' etc pinouts.morzh — 12:46 PM
Part numbers to model cross
Thank you morzh, that is exactly what I was looking for. Now , is there some where that shows pinouts for Philco power ...Jim Dutridge — 11:37 AM
Restoration of the Canadian General Electric A-87
Thanks for your help Michael. In fact, this video is only an intermediate result. Later I had to apply another tinting l...RadioSvit — 09:01 AM
Restoration of the Canadian General Electric A-87
Great job on the cabinet. PS. In the US notation, "kenotron" refers to specific type of tubes; we call re...morzh — 08:24 AM
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. Search f...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM

[-]
Who's Online
There are currently 1313 online users. [Complete List]
» 1 Member(s) | 1312 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration