volume control

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

volume control

Radioroslyn
Phorum Expert

Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa

10-15-2011, 10:41 PM

If it is for the model 80 it's 20K. Two quick checks, one unplug set turn volume all the way up. Measure resistance from ANT post to chassis ground. Should be very low like a few ohms. If not antenna coil primary is open. Two, Turn volume all the away down.Measure resistance from antenna post to chassis ground. Should read about 20,000 ohms. If not check volume control, open or bad ground connection.
How's your oscillator doing?
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

volume control - by johnfin - 10-15-2011, 10:24 PM

Re: volume control - by 7estatdef - 10-15-2011, 10:41 PM

Re: volume control - by ipwizard - 10-15-2011, 10:42 PM

Re: volume control - by Ron Ramirez - 10-16-2011, 07:30 AM

Re: volume control - by 7estatdef - 10-16-2011, 08:06 AM

Re: volume control - by Ron Ramirez - 10-16-2011, 09:17 AM

Re: volume control - by johnfin - 10-16-2011, 10:11 AM

Re: volume control - by codefox1 - 10-16-2011, 11:24 AM

Re: volume control - by 7estatdef - 10-16-2011, 06:02 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

Who's Online

There are currently 968 online users. [Complete List]
» 2 Member(s) | 966 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me