1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Spray Lacquer Question?
Pepperoni
Member
***
Posts: 160
Threads: 42
Joined: Apr 2011
City: New Port Richey State, Province, Country: Florida
#1

10-24-2011, 07:33 PM
I stained the cabinet on this 40-190 this morning. I had to strip someones rather poor attempt to refinish it sometime in the past. I've used Deft lacquer "sanding sealer" before on new veneer but is it necessary to use it when refinishing a cabinet that has had no new veneer put on it? Can I just shoot the finish lacquer over the stain once it's good and dry?

Thanks,
Pepper
"It's Nice To Be Nice To The Nice"
Major Frank Burns Mash 4077th
Website Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Spray Lacquer Question? - by Pepperoni - 10-24-2011, 07:33 PM
RE: Spray Lacquer Question? - by Ron Ramirez - 02-28-2012, 07:13 PM
RE: Spray Lacquer Question? - by codefox1 - 02-28-2012, 11:31 PM
RE: Spray Lacquer Question? - by squeeker7 - 03-03-2012, 05:36 PM
RE: Spray Lacquer Question? - by ipwizard - 03-06-2012, 02:33 PM
RE: Spray Lacquer Question? - by TA Forbes - 03-06-2012, 02:38 PM
RE: Spray Lacquer Question? - by magicclocks - 04-22-2012, 05:57 PM
RE: Spray Lacquer Question? - by LedHed - 04-25-2012, 01:01 AM
RE: Spray Lacquer Question? - by Ron Ramirez - 04-25-2012, 07:32 AM
RE: Spray Lacquer Question? - by Pepperoni - 04-29-2012, 04:34 PM
RE: Spray Lacquer Question? - by gary rabbitt - 06-11-2012, 06:44 PM
Re: Spray Lacquer Question? - by exray - 10-25-2011, 06:02 AM
Re: Spray Lacquer Question? - by Pepperoni - 10-26-2011, 11:19 AM
RE: Spray Lacquer Question? - by Pepperoni - 02-28-2012, 07:08 PM
RE: Spray Lacquer Question? - by 37silverstreak - 02-28-2012, 08:56 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM
Philco model 38 code 121 not receiving signal.
Good news everyone! I think I have found everything I need for rewinding the antenna coil primary. I found some pla...Stormlord5500 — 09:40 AM
Philco Battery-WWII vintage
My younger sister went to SUNY Plattsburg NY, (BS, MS, RN) in the late 1970sabout 10 min from the Northern NY / Canada b...MrFixr55 — 07:59 AM

[-]
Who's Online
There are currently 1803 online users. [Complete List]
» 3 Member(s) | 1800 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration