Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

Philco 71 restoration
#24

Well did you rewind the coil? I suppose it may be possible that the noise is coming from the oscillator but I would be more focused on getting it to play than the noise. Sometimes once it's working these little issue go away so I tend to work on the big stuff and let the little stuff fall into place.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got it!

Terry


Messages In This Thread
Philco 71 restoration - by Keith - 09-29-2011, 12:48 AM
RE: Philco 71 restoration - by Keith - 03-02-2012, 06:09 PM
Re: Man this thing is a nightmare - by Keith - 09-29-2011, 01:36 AM
Re: Man this thing is a nightmare - by Keith - 09-29-2011, 10:14 PM
Re: Man this thing is a nightmare - by Keith - 10-06-2011, 12:29 AM
Re: Man this thing is a nightmare - by Arran - 10-06-2011, 02:24 AM
Re: Man this thing is a nightmare - by rghines1 - 10-06-2011, 10:20 AM
Re: Man this thing is a nightmare - by exray - 10-06-2011, 12:41 PM
Re: Man this thing is a nightmare - by Keith - 10-08-2011, 10:34 PM
Re: Man this thing is a nightmare - by Marsupial - 10-08-2011, 11:52 PM
Re: Man this thing is a nightmare - by exray - 10-09-2011, 05:56 AM
Re: Man this thing is a nightmare - by Keith - 10-10-2011, 01:40 PM
Re: Philco 71 restoration - by Keith - 10-31-2011, 05:10 PM
Re: Philco 71 restoration - by 7estatdef - 10-31-2011, 08:48 PM
Re: Philco 71 restoration - by 7estatdef - 10-31-2011, 09:00 PM
Re: Philco 71 restoration - by Keith - 11-01-2011, 01:03 AM
Re: Philco 71 restoration - by Keith - 11-01-2011, 01:06 AM
Re: Philco 71 restoration - by 7estatdef - 11-01-2011, 10:58 PM
Re: Philco 71 restoration - by Keith - 11-03-2011, 01:03 AM
Re: Philco 71 restoration - by 7estatdef - 11-03-2011, 02:59 AM
Re: Philco 71 restoration - by codefox1 - 11-03-2011, 10:04 AM
Re: Philco 71 restoration - by Keith - 11-03-2011, 06:00 PM
Re: Philco 71 restoration - by 7estatdef - 11-03-2011, 06:26 PM
Re: Philco 71 restoration - by Keith - 11-03-2011, 06:31 PM
Re: Philco 71 restoration - by 7estatdef - 11-03-2011, 06:42 PM
Re: Philco 71 restoration - by Keith - 11-03-2011, 07:40 PM
Re: Philco 71 restoration - by 7estatdef - 11-03-2011, 08:39 PM
Re: Philco 71 restoration - by Keith - 11-03-2011, 09:38 PM
Re: Philco 71 restoration - by Keith - 11-04-2011, 12:29 AM
Re: Philco 71 restoration - by Keith - 11-04-2011, 02:33 PM
Re: Philco 71 restoration - by Keith - 11-30-2011, 11:56 PM
Re: Philco 71 restoration - by TA Forbes - 12-01-2011, 12:37 AM
Re: Philco 71 restoration - by TA Forbes - 12-02-2011, 09:54 PM
Re: Philco 71 restoration - by codefox1 - 12-03-2011, 11:48 AM
Re: Philco 71 restoration - by Keith - 12-04-2011, 03:03 PM
Re: Philco 71 restoration - by Keith - 12-23-2011, 04:36 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
That looks a lot like an aircraft connector of some kind, even if it's a U.S.N power supply. I have a book somewhere abo...Arran — 02:56 AM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
hello david, I have a similar generator in my collection that features a cast iron, single-cylinder Briggs & Stratt...radiorich — 01:00 AM
under chassis parts locator diagram for 1938 Zenith 9s262
Has anyone gone to the trouble of creating an under chassis parts locator image?  Yes, I can identify components by foll...bobloney — 08:57 PM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
Try looking at this site the book mark is for a old generator that I was given. David    https://radionerds.com/index.ph...David — 08:36 PM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
Hello Everyone, I am looking for voltage identification for all the pin positions on the socket of a CRV-20130 power su...Tonym4704 — 08:16 PM
Philco P45-6365 Universal Transformer Instruction Manual
Can anyone guide me to where this may be found?GRG — 03:00 PM
54C Complete Teardown/Rebuild
I don't think that I have encountered a 12Z3 before, curious how it uses one of those but includes a #43, which is a 25 ...Arran — 02:17 PM
HiFi (Chifi) tube amp build - but my own design.
It's the other forum. I'm also in DIY, but mostly read there. Honestly, I kinda jumped into this without much thought to...TV MAN — 10:43 AM
Philco 71 Code 125
Hello,  I am in need of a schematic for this radio. Mine has the three separate circular tube shields and a shadow me...dconant — 08:06 AM
Stromberg Carlson 1500 Squeal
And life just keeps getting more complicated.dconant — 07:57 AM

[-]
Who's Online
There are currently no members online.

>