Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 60 Part ID
#3

The center dot looks painted, you can see wrinkles around the edges of the center dot which I don't think would be there if it wasn't painted, then again they usualy tried to use a contasting shade of brown. So it is orange brown orange, or 31,000 micro micro farads (picofarad in new lingo) for the first one, and 610,000 MMF for the second, both are supposedly rated for 500 volts if I read them correctly. They don't look physically large enough to be that because those values are huge for a mica capacitor? If you divide 610,000 MMF by 10,000 that comes up as a .61 microfarad capacitor, maybe it's supposed to be 64 mmf (pf) cap and the other a 33 mmf cap? Are those on the schematic?
Regards
Arran


Messages In This Thread
Model 60 Part ID - by Caperodder - 11-03-2011, 04:54 PM
Re: Model 60 Part ID - by PhilcoMike - 11-04-2011, 09:02 AM
Re: Model 60 Part ID - by Arran - 11-05-2011, 11:30 PM
Re: Model 60 Part ID - by Caperodder - 11-06-2011, 08:24 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Restoration of the Canadian General Electric A-87
Well... The console body has been restored, while the varnish dries reliably I started repairing the chassis.. ...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM
Philco 42-345 Restoration/Repair
What does the resistor measure? I think it should be 3.3 Meg. If the oscillator coil has continuity and the resistanc...RodB — 09:03 PM
Philco Model 38-7: what caps & resistors do fail typically?
Good idea to check the coils... then I'll get hold of an incadescent light bulb and see what happens when the unit is sw...Musaeum — 08:49 PM
Philco 42-345 Restoration/Repair
I have that same set, ain't too much shortwave I like anyway.....it is a good AM DX set. PaulPaul Philco322 — 08:32 PM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum, Martin! Open a new thread in Philco Electronic Restoration when you begin working on your 38-7. ...GarySP — 08:28 PM

[-]
Who's Online
There are currently 949 online users. [Complete List]
» 2 Member(s) | 947 Guest(s)
AvatarAvatar

>