1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Restoring 38-7CS cabinet
peterc
Junior Member
**
Posts: 8
Threads: 2
Joined: Jan 2011
#6

12-28-2011, 10:21 PM
To All,
I bought a knob from Mike Koste, purchased Mohawk lacquer toner/clear finish from a local Mohawk distributer (about 45 mins drive, 7.11/can).
Questions-not my last!-
1. again what is the preferred way to protect the "PHILCO" logo?
2. any tricks to disassembling the electronics and speaker from the cabinet? I haven't even looked under there except to verify that it is a 38-7CS.

I really appreciate the knowledge and the willingness of the phorum members to share!
Pete
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Restoring 38-7CS cabinet - by peterc - 12-14-2011, 10:22 AM
Re: Restoring 38-7CS cabinet - by Bob Andersen - 12-16-2011, 12:58 PM
Re: Restoring 38-7CS cabinet - by peterc - 12-17-2011, 09:08 AM
Re: Restoring 38-7CS cabinet - by Ron Ramirez - 12-17-2011, 09:50 AM
Re: Restoring 38-7CS cabinet - by Bob Andersen - 12-17-2011, 08:29 PM
Re: Restoring 38-7CS cabinet - by peterc - 12-28-2011, 10:21 PM
Re: Restoring 38-7CS cabinet - by LASJayhawk - 12-29-2011, 03:03 AM
Re: Restoring 38-7CS cabinet - by peterc - 12-29-2011, 10:35 AM
Re: Restoring 38-7CS cabinet - by Bob Andersen - 01-01-2012, 04:55 PM
Re: Restoring 38-7CS cabinet - by peterc - 01-02-2012, 10:04 PM
Re: Restoring 38-7CS cabinet - by fixinmyphilco - 01-19-2012, 08:05 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration