1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
The 37-650 from H**l
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#3

12-30-2011, 09:52 PM
I feel your pain. I had an intermittant issue wiith my 38-665. Lost volume/reception. When I placed a screwdriver on the 6A8, cam in loud and clear. Hmmmmm, RF deck prob.

Turned out to be one of the very thin wires in the RF Unit portion of the RF deck was broken and making intermittant ctc. I repaired this, and since I had the d**n deck out of the radio I replaced the caps deep in the deck, which was somthing I had been putting off until the Radio Fairy blessed me.

Plays well now. Worth the effort, but those RF decks are a pain in the ____ (thing one sits on).
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
The 37-650 from H**l - by Ron Ramirez - 12-30-2011, 07:43 PM
Re: The 37-650 from h**l - by Glenn Roberts - 12-30-2011, 07:56 PM
Re: The 37-650 from h**l - by TA Forbes - 12-30-2011, 09:52 PM
Re: The 37-650 from h**l - by 7estatdef - 12-30-2011, 10:47 PM
Re: The 37-650 from h**l - by Ron Ramirez - 12-30-2011, 11:28 PM
Re: The 37-650 from h**l - by BDM - 12-31-2011, 01:01 AM
Re: The 37-650 from h**l - by Chuck Schwark - 12-31-2011, 05:39 PM
Re: The 37-650 from h**l - by Steve Davis - 12-31-2011, 06:46 PM
Re: The 37-650 from h**l - by Texasrocker - 12-31-2011, 11:21 PM
Re: The 37-650 from h**l - by Arran - 01-02-2012, 11:59 PM
Re: The 37-650 from h**l - by TA Forbes - 01-03-2012, 03:19 PM
Re: The 37-650 from h**l - by TA Forbes - 01-03-2012, 03:22 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 719 online users. [Complete List]
» 1 Member(s) | 718 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration