1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Model 42-380 veneer
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#3

11-02-2006, 10:12 AM
Steve

Probably walnut veneer on your 42-380. Not the figured, fancy tiger or "butt" walnut, just a plain pattern. It will match the grain pattern on the top left and right panels, and run from front to back - vertically where it bends over to cover the front where the hole for the dial and knob shaft holes are.

I'll ditto Chuck's recommendation of Dick Oliver to make a replacement panel for your 70. He does fantastic work. He's listed on the PhilcoRadio.com Resources page also. By the way, he also does refinishing, cabinet repair, and even makes complete reproduction cabinets for the 20, 70 and 90 cathedrals.
--
Ron Ramirez
Ferdinand IN
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Model 42-380 veneer - by Steve D - 11-02-2006, 09:37 AM
[No subject] - by Chuck Schwark - 11-02-2006, 09:50 AM
[No subject] - by Ron Ramirez - 11-02-2006, 10:12 AM
[No subject] - by Terry Burns - 11-02-2006, 10:31 AM
[No subject] - by Steve D - 11-02-2006, 02:59 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently 938 online users. [Complete List]
» 2 Member(s) | 936 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration