1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 38-7Cs Identify these parts
ipwizard
Senior Member
****
Posts: 335
Threads: 50
Joined: Apr 2011
City: Apple Creek State, Province, Country: Ohio
#5

01-20-2012, 05:37 PM
Crap. The round deal is not a part 8 the 3500uuf cap that cap in mounted in front of the wafer switch.

My guess #2 or is it 3 whatever is that the round deal is a thermal compensator which I do not see listed on the parts diagram or parts list. In the changes for the set it states that in Run # 3 a new thermal compensator was connected in parallel with compensator # 7A and mounted near resistor #12. The the round doodad is mounted right next to the power resistor #12 in the original photos.

On the right side of your top photo the taller compensator is 7A and has the round thermal compensator in parallel with it, and the other compensator is #7 on the schematic.

List of Changes from Riders: Read the Run 3 details.
[Image: http://i1129.photobucket.com/albums/m501...hanges.jpg]

Then the thermal compensator was replaced with two fixed caps in run 4.
-Keith
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco 38-7Cs Identify these parts - by mukerjea - 01-17-2012, 10:41 PM
Re: Philco 38-7Cs Identify these parts - by ipwizard - 01-20-2012, 05:37 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
So one last question before I finish this radio. Regarding the speaker and output transformer. I salvaged the original o...Stormlord5500 — 09:31 AM
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM
Model 70 Cabinet Trim
Steve might have some trim left. Not sure he is making anything.morzh — 06:12 AM
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM

[-]
Who's Online
There are currently 517 online users. [Complete List]
» 1 Member(s) | 516 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration