Philco model 20

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco model 20

fabignoli
Junior Member

Posts: 12
Threads: 3
Joined: Nov 2006

12-04-2006, 06:26 AM

Hello Ron,

Actually I'm working on a small 2 tubes RF generator project. I will finish it this week or next week. After that, I will try to re-start the philco Icon_rolleyes

. Lot of work I'm afraid Icon_lol

Lot of rust inside, the 71A are out of order (I've not received the new one, but before I can take 2 of the in an atwater 46), I've got 3 ou 4 24, so for the tubes its OK.

I hope that the AC transformer is ok, because it's long to rewind but if it's not, I will do it. I pray for the 3 RF coils but they are not difficult to rewind.

SO, for the photo it's ok, but Iif you don't mind, please wait one week or two. Many thak's Ron. Your forum is great....

best regards
Frederic ABIGNOLI

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Philco model 20 - by Guest - 04-18-2006, 11:18 PM

[No subject] - by Chuck Schwark - 04-18-2006, 11:31 PM

[No subject] - by fabignoli - 12-01-2006, 05:57 AM

[No subject] - by Ron Ramirez - 12-01-2006, 10:39 AM

[No subject] - by fabignoli - 12-04-2006, 06:26 AM

[No subject] - by fabignoli - 12-16-2006, 12:31 PM

[No subject] - by Chuck Schwark - 12-16-2006, 05:56 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online

There are currently 719 online users. [Complete List]
» 1 Member(s) | 718 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me