Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

Philco 84
#18

(04-09-2012, 02:19 PM)Jim Dutridge Wrote:  Not sure what gauge wire I'm using. I pulled off an old Majestice field coil. Its pretty thin, and yes, let the fun begin. I do have some 40 gauge and 34 guage. Which would be better choice and would I just match the original number of turns with either?

Well the 34 would be a bit easier to work with. I would add a few extra turns to makeup for the size difference. Make sure that you wind it in the same direction as the original else it won't oscillate.
Terry



Messages In This Thread
Philco 84 - by Jim Dutridge - 04-03-2012, 03:39 PM
RE: Philco 84 - by Ron Ramirez - 04-03-2012, 04:18 PM
RE: Philco 84 - by Jim Dutridge - 04-03-2012, 04:29 PM
RE: Philco 84 - by Art Hoch - 04-03-2012, 08:10 PM
RE: Philco 84 - by Jim Dutridge - 04-03-2012, 09:04 PM
RE: Philco 84 - by Ron Ramirez - 04-03-2012, 09:31 PM
RE: Philco 84 - by Jim Dutridge - 04-05-2012, 05:11 PM
RE: Philco 84 - by Art Hoch - 04-05-2012, 09:49 PM
RE: Philco 84 - by Jim Dutridge - 04-07-2012, 01:09 PM
RE: Philco 84 - by 7estatdef - 04-07-2012, 02:09 PM
RE: Philco 84 - by Jim Dutridge - 04-08-2012, 10:48 AM
RE: Philco 84 - by 7estatdef - 04-08-2012, 04:48 PM
RE: Philco 84 - by Jim Dutridge - 04-08-2012, 11:08 AM
RE: Philco 84 - by 7estatdef - 04-08-2012, 04:58 PM
RE: Philco 84 - by Jim Dutridge - 04-09-2012, 09:56 AM
RE: Philco 84 - by 7estatdef - 04-09-2012, 01:58 PM
RE: Philco 84 - by Jim Dutridge - 04-09-2012, 02:19 PM
RE: Philco 84 - by 7estatdef - 04-09-2012, 03:38 PM
RE: Philco 84 - by Jim Dutridge - 04-10-2012, 04:23 PM
RE: Philco 84 - by 7estatdef - 04-10-2012, 07:28 PM
RE: Philco 84 - by Jim Dutridge - 04-11-2012, 05:47 PM
RE: Philco 84 - by Jim Dutridge - 04-15-2012, 12:18 PM
RE: Philco 84 - by 7estatdef - 04-15-2012, 03:31 PM
RE: Philco 84 - by Jim Dutridge - 04-15-2012, 06:37 PM
RE: Philco 84 - by Jim Dutridge - 05-11-2012, 04:10 PM
RE: Philco 84 - by 7estatdef - 05-13-2012, 08:42 AM
RE: Philco 84 - by Jim Dutridge - 05-15-2012, 03:31 PM
RE: Philco 84 - by Jim Dutridge - 05-31-2012, 04:34 PM
RE: Philco 84 - by 7estatdef - 05-31-2012, 08:12 PM
RE: Philco 84 - by Jim Dutridge - 05-31-2012, 11:06 PM
RE: Philco 84 - by 7estatdef - 06-01-2012, 06:35 AM
RE: Philco 84 - by Jim Dutridge - 06-01-2012, 03:20 PM
RE: Philco 84 - by 7estatdef - 06-01-2012, 03:40 PM
RE: Philco 84 - by Jim Dutridge - 06-04-2012, 03:55 PM
RE: Philco 84 - by Jim Dutridge - 06-12-2012, 05:37 PM
RE: Philco 84 - by 7estatdef - 06-13-2012, 08:59 PM
RE: Philco 84 - by Jim Dutridge - 06-15-2012, 04:00 PM
RE: Philco 84 - by Jim Dutridge - 10-14-2014, 06:19 PM
RE: Philco 84 - by morzh - 10-14-2014, 07:27 PM
RE: Philco 84 - by Jim Dutridge - 10-14-2014, 08:01 PM
RE: Philco 84 - by morzh - 10-14-2014, 10:10 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
54C Complete Teardown/Rebuild
Hello Roy, here is this one sincerely Richardradiorich — 12:45 AM
54C Complete Teardown/Rebuild
Richard, Had grabbed it already but thank you just the same.  I find myself wanting to find some way to block out the...glyphmon — 12:03 AM
54C Complete Teardown/Rebuild
Hello roy, here is a link to the schematic . Sincerely Richardradiorich — 11:54 PM
54C Complete Teardown/Rebuild
Richard, The Silvertone 2014 also is a transformerless set, so I am incorporating a 1:1 600 ohm audio isolation transfo...glyphmon — 11:37 PM
Preliminary work on wife's Silvertone 2014
Did an alignment today which was interesting.  IF alignment went great, almost all was already spot-on.  Adjusting on th...glyphmon — 11:35 PM
54C Complete Teardown/Rebuild
The main problem with adding a Bluetooth input is that this set lacks a traditional power transformer to isolate it from...radiorich — 11:19 PM
54C Cabinet Refinish
I started stripping this cabinet before it got super chilly out because I knew I wasn't going to be able to work on ...glyphmon — 11:18 PM
54C Complete Teardown/Rebuild
While I'm waiting to wrap up the final steps on my wife's Silvertone 2014, I started disassembly on the next project.  O...glyphmon — 11:07 PM
Preliminary work on wife's Silvertone 2014
Hello roy, that great news glad it worked out for you !! Sincerely Richardradiorich — 10:50 PM
Preliminary work on wife's Silvertone 2014
Safety caps arrived today.  Soldered one in and had a successful first power-up.  No magic smoke escaped and it tunes in...glyphmon — 09:53 PM

[-]
Who's Online
There are currently no members online.

>