1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 84
Radioroslyn
Phorum Expert
*****
Posts: 7,305
Threads: 270
Joined: Dec 2009
City: Roslyn Pa
#20

04-10-2012, 07:28 PM
Hey Jim,
You aren't going to like my answer but what I do when there is a space between the turns is I lay down two windings side by side. One is the inductor and the other is a spacer. Once the coil is wound the spacer winding is removed.
You can leave yours as is but I'll bet that the set won't track properly and It will be low in frequency because your coil is going to be too high in inductance.
As for the feedback winding (small winding) I don't think I've ever seen one that has space between the turns. It's just would one next to the other. Just wound one up for a member the other night.
Fingers cramping yet???
GL
Terry
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco 84 - by Jim Dutridge - 04-03-2012, 03:39 PM
RE: Philco 84 - by Ron Ramirez - 04-03-2012, 04:18 PM
RE: Philco 84 - by Jim Dutridge - 04-03-2012, 04:29 PM
RE: Philco 84 - by Art Hoch - 04-03-2012, 08:10 PM
RE: Philco 84 - by Jim Dutridge - 04-03-2012, 09:04 PM
RE: Philco 84 - by Ron Ramirez - 04-03-2012, 09:31 PM
RE: Philco 84 - by Jim Dutridge - 04-05-2012, 05:11 PM
RE: Philco 84 - by Art Hoch - 04-05-2012, 09:49 PM
RE: Philco 84 - by Jim Dutridge - 04-07-2012, 01:09 PM
RE: Philco 84 - by 7estatdef - 04-07-2012, 02:09 PM
RE: Philco 84 - by Jim Dutridge - 04-08-2012, 10:48 AM
RE: Philco 84 - by 7estatdef - 04-08-2012, 04:48 PM
RE: Philco 84 - by Jim Dutridge - 04-08-2012, 11:08 AM
RE: Philco 84 - by 7estatdef - 04-08-2012, 04:58 PM
RE: Philco 84 - by Jim Dutridge - 04-09-2012, 09:56 AM
RE: Philco 84 - by 7estatdef - 04-09-2012, 01:58 PM
RE: Philco 84 - by Jim Dutridge - 04-09-2012, 02:19 PM
RE: Philco 84 - by 7estatdef - 04-09-2012, 03:38 PM
RE: Philco 84 - by Jim Dutridge - 04-10-2012, 04:23 PM
RE: Philco 84 - by 7estatdef - 04-10-2012, 07:28 PM
RE: Philco 84 - by Jim Dutridge - 04-11-2012, 05:47 PM
RE: Philco 84 - by Jim Dutridge - 04-15-2012, 12:18 PM
RE: Philco 84 - by 7estatdef - 04-15-2012, 03:31 PM
RE: Philco 84 - by Jim Dutridge - 04-15-2012, 06:37 PM
RE: Philco 84 - by Jim Dutridge - 05-11-2012, 04:10 PM
RE: Philco 84 - by 7estatdef - 05-13-2012, 08:42 AM
RE: Philco 84 - by Jim Dutridge - 05-15-2012, 03:31 PM
RE: Philco 84 - by Jim Dutridge - 05-31-2012, 04:34 PM
RE: Philco 84 - by 7estatdef - 05-31-2012, 08:12 PM
RE: Philco 84 - by Jim Dutridge - 05-31-2012, 11:06 PM
RE: Philco 84 - by 7estatdef - 06-01-2012, 06:35 AM
RE: Philco 84 - by Jim Dutridge - 06-01-2012, 03:20 PM
RE: Philco 84 - by 7estatdef - 06-01-2012, 03:40 PM
RE: Philco 84 - by Jim Dutridge - 06-04-2012, 03:55 PM
RE: Philco 84 - by Jim Dutridge - 06-12-2012, 05:37 PM
RE: Philco 84 - by 7estatdef - 06-13-2012, 08:59 PM
RE: Philco 84 - by Jim Dutridge - 06-15-2012, 04:00 PM
RE: Philco 84 - by Jim Dutridge - 10-14-2014, 06:19 PM
RE: Philco 84 - by morzh - 10-14-2014, 07:27 PM
RE: Philco 84 - by Jim Dutridge - 10-14-2014, 08:01 PM
RE: Philco 84 - by morzh - 10-14-2014, 10:10 PM



Users browsing this thread:
[-]
Recent Posts
Philco Model 38-7: what caps & resistors do fail typically?
Since you stated earlier, you have a console 38-7XX.  They also had a 38-7T (table), and 38-7CS (chairside).  A very nic...GarySP — 01:18 PM
Part numbers to model cross
That I wouldn't know, but sometimes the radio document itself shows one, same as the capacitor cans' etc pinouts.morzh — 12:46 PM
Part numbers to model cross
Thank you morzh, that is exactly what I was looking for. Now , is there some where that shows pinouts for Philco power ...Jim Dutridge — 11:37 AM
Restoration of the Canadian General Electric A-87
Thanks for your help Michael. In fact, this video is only an intermediate result. Later I had to apply another tinting l...RadioSvit — 09:01 AM
Restoration of the Canadian General Electric A-87
Great job on the cabinet. PS. In the US notation, "kenotron" refers to specific type of tubes; we call re...morzh — 08:24 AM
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. Search f...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration