1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Model 90 Stuck At One Volume Level
morzh
Odobenus rosmarus
******
Posts: 16,510
Threads: 572
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#17

04-15-2012, 01:04 PM
Pepper,

Whatr I meant was: If it stops playing after yanking, then PUT IT BACK first, then keep yanking to the left (towards the Antenna.)
I missed "put it back first". Without putting it back there will be no need yanking anything else, of course.

What I wanted to see if there is a tube to the left of teh Detamp that you can yank, and it would still play.


So, now: 1) Put DetAmp back (we know it stops playing when you pull it), and 2) yank the previous tube (det. Rectifier)

Does it still play?.


PS. This proverb in Russian sounds "You may call me a pot, just don't put me in the oven" Icon_smile
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Model 90 Stuck At One Volume Level - by Pepperoni - 04-12-2012, 04:54 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-12-2012, 10:19 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-14-2012, 03:44 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-14-2012, 03:52 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-14-2012, 07:16 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-14-2012, 09:51 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-15-2012, 01:04 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-15-2012, 02:26 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM
Electrolytic restuffing/internals
I have an issue on a non-Philco radio which I expect to run into on a whole set of Philcos and others. I have an 8mf ...bridkarl — 01:17 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. I thought about it and decided to put it up in the arch support. I was looking at the chassis and didn't ...Stormlord5500 — 06:24 AM
Philco model 38 code 121 not receiving signal.
Congrats on your success Stormlord. My rough guess is that since both the 15 and the 1A6 are supposed to be shielded, I...MrFixr55 — 10:04 PM
The list of my radio & TV collection!
A little light Saturday positive about our hobby in our feed... My new every Saturday video about antique radio equipme...RadioSvit — 02:12 PM

[-]
Who's Online
There are currently 708 online users. [Complete List]
» 4 Member(s) | 704 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration