philco 48-214 code 125 Cap ?

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

philco 48-214 code 125 Cap ?

Arran
Phorum Expert

Posts: 4,894
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA

#9

05-23-2012, 11:25 PM

If the set uses a 35Y4, a 35Z5, or a 35W4 tube then it likely has one of two things wrong:
(1) The rectifier tube heater is open between the pilot light tap and one end of the tube heater.
(2 The resistor paralleled with the pilot light is open circuit or blown. With some tubes like the 35Y4 it may or may not have a resistor paralleled with the pilot light depending on the amperage of the pilot light bulb used.
Regards
Arran

Find

« Next Oldest | Next Newest »

Messages In This Thread

philco 48-214 code 125 Cap ? - by Eric - 05-20-2012, 01:18 PM

RE: philco 48-214 code 125 Cap ? - by codefox1 - 05-20-2012, 02:17 PM

RE: philco 48-214 code 125 Cap ? - by Eric - 05-20-2012, 03:10 PM

RE: philco 48-214 code 125 Cap ? - by Arran - 05-20-2012, 09:18 PM

RE: philco 48-214 code 125 Cap ? New problem - by Eric - 05-23-2012, 05:24 PM

RE: philco 48-214 code 125 Cap ? - by morzh - 05-23-2012, 08:37 PM

RE: philco 48-214 code 125 Cap ? - by 7estatdef - 05-23-2012, 09:07 PM

RE: philco 48-214 code 125 Cap ? - by morzh - 05-23-2012, 09:10 PM

RE: philco 48-214 code 125 Cap ? - by Arran - 05-23-2012, 11:25 PM

RE: philco 48-214 code 125 Cap ? - by morzh - 05-24-2012, 09:28 AM

RE: philco 48-214 code 125 Cap ? - by Eric - 05-24-2012, 03:14 PM

RE: philco 48-214 code 125 Cap ? - by codefox1 - 05-24-2012, 10:13 PM

RE: philco 48-214 code 125 Cap ? - by Eric - 05-29-2012, 03:08 PM

RE: philco 48-214 code 125 Cap ? - by 7estatdef - 05-30-2012, 07:15 AM

RE: philco 48-214 code 125 Cap ? - by morzh - 05-30-2012, 08:25 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online

There are currently 762 online users. [Complete List]
» 1 Member(s) | 761 Guest(s)