1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Nobody else wanted it...
gary rabbitt
Senior Member
****
Posts: 271
Threads: 12
Joined: Nov 2005
City: Nashville, TN
#2

06-11-2012, 12:41 PM
Hi Terry,
You got a very good deal on this. The top will need to be reveneered for sure, you may find that the sides can be saved.
Worst case, the trans and field coil are bad, but you will still come out ahead if you were to repair those.
I would have bought it too if it were local, but lately I have been running out of room. (Due to too many other consoles.)
Good luck.
(This post was last modified: 06-11-2012, 12:43 PM by gary rabbitt.)
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Nobody else wanted it... - by 7estatdef - 06-11-2012, 12:35 PM
RE: Nobody else wanted it... - by gary rabbitt - 06-11-2012, 12:41 PM
RE: Nobody else wanted it... - by Arran - 06-11-2012, 06:03 PM
RE: Nobody else wanted it... - by 7estatdef - 06-11-2012, 08:30 PM
RE: Nobody else wanted it... - by Arran - 06-11-2012, 09:03 PM
RE: Nobody else wanted it... - by 7estatdef - 06-11-2012, 09:24 PM
RE: Nobody else wanted it... - by TA Forbes - 06-11-2012, 09:41 PM
RE: Nobody else wanted it... - by morzh - 06-11-2012, 10:31 PM
RE: Nobody else wanted it... - by 7estatdef - 06-11-2012, 10:53 PM
RE: Nobody else wanted it... - by Tom Hamilton - 06-12-2012, 01:42 PM
RE: Nobody else wanted it... - by Michael Gerber - 06-12-2012, 01:55 PM
RE: Nobody else wanted it... - by 7estatdef - 06-18-2012, 05:22 PM
RE: Nobody else wanted it... - by Chicago Jimmy - 06-18-2012, 07:32 PM
RE: Nobody else wanted it... - by 7estatdef - 07-26-2012, 01:21 AM
RE: Nobody else wanted it... - by codefox1 - 07-26-2012, 10:54 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios