Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Nobody else wanted it...
#3

With regard to the top, it looks like only the middle section is chipped so the two end sections could likley be salvaged. I noticed that there is a chip out of the top of the left side pilaster (curved area) I don't know if that is teh same cut or species as the top but perhaps the top veneer could be used to patch it? I'm not surprised that nobody else wanted it but there is a swan under that ugly duckling to be found if the veneer repairs are carried out the right way. This set is typical of the bargain consoles I find, although it is also dirtier then the last few I picked up.
Regards
Arran


Messages In This Thread
Nobody else wanted it... - by 7estatdef - 06-11-2012, 12:35 PM
RE: Nobody else wanted it... - by gary rabbitt - 06-11-2012, 12:41 PM
RE: Nobody else wanted it... - by Arran - 06-11-2012, 06:03 PM
RE: Nobody else wanted it... - by 7estatdef - 06-11-2012, 08:30 PM
RE: Nobody else wanted it... - by Arran - 06-11-2012, 09:03 PM
RE: Nobody else wanted it... - by 7estatdef - 06-11-2012, 09:24 PM
RE: Nobody else wanted it... - by TA Forbes - 06-11-2012, 09:41 PM
RE: Nobody else wanted it... - by morzh - 06-11-2012, 10:31 PM
RE: Nobody else wanted it... - by 7estatdef - 06-11-2012, 10:53 PM
RE: Nobody else wanted it... - by Tom Hamilton - 06-12-2012, 01:42 PM
RE: Nobody else wanted it... - by Michael Gerber - 06-12-2012, 01:55 PM
RE: Nobody else wanted it... - by 7estatdef - 06-18-2012, 05:22 PM
RE: Nobody else wanted it... - by Chicago Jimmy - 06-18-2012, 07:32 PM
RE: Nobody else wanted it... - by 7estatdef - 07-26-2012, 01:21 AM
RE: Nobody else wanted it... - by codefox1 - 07-26-2012, 10:54 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>