1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Model 600 cabinet
Steve D
Member
***
Posts: 116
Threads: 25
Joined: Jul 2006
City: Lebanon, NJ 08833
#1

07-02-2012, 04:36 PM
I am working on what I think is a 600C or a 602C and the cabinet was in terrible condition with lots of delamination. I have it mostly glued and veneered back together but have a question about the radio back.

My back is separate and appears that it is supposed to be glued to the cabinet. I presume the radio chassis which mounts from the bottom can be installed with the rear cover glued on but I am not sure. The back has about a 1/64" wood laminate on the inside of the cover for strength but mine only has a piece across the top. Does anyone know what size this laminate should be and how the speaker grille cloth is fastened to it. (there are two grille clothes, one on the front in front of the speaker and one on the back panel.

Thanks,

Steve D
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Model 600 cabinet - by Steve D - 07-02-2012, 04:36 PM
RE: Model 600 cabinet - by Ron Ramirez - 07-02-2012, 06:30 PM
RE: Model 600 cabinet - by 7estatdef - 07-02-2012, 11:06 PM
RE: Model 600 cabinet - by Steve D - 07-03-2012, 10:07 AM
RE: Model 600 cabinet - by Ron Ramirez - 07-03-2012, 10:20 AM
RE: Model 600 cabinet - by Arran - 07-03-2012, 09:29 PM
RE: Model 600 cabinet - by codefox1 - 07-04-2012, 11:33 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM
Philco model 38 code 121 not receiving signal.
Good news everyone! I think I have found everything I need for rewinding the antenna coil primary. I found some pla...Stormlord5500 — 09:40 AM
Philco Battery-WWII vintage
My younger sister went to SUNY Plattsburg NY, (BS, MS, RN) in the late 1970sabout 10 min from the Northern NY / Canada b...MrFixr55 — 07:59 AM

[-]
Who's Online
There are currently 1774 online users. [Complete List]
» 3 Member(s) | 1771 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration