Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

New 18
#7

Philament, don't throw out the old tubes. I can't tell you how many I have replaced that measured real low on the tube tester and the new ones didn't make any difference in performance. Dead, yes replace. I have a pair of 45s on my latest project that are in the 8 to 10 percent range on conductance and yet seem to be working well. All the other tubes are in the "replace" mode but still seem fine. We will see how things go and I get into the radio (a 111 philco).

Good luck
Jerry

A friend in need is a pest!  Bill Slee ca 1970.


Messages In This Thread
New 18 - by Philament - 06-30-2012, 08:31 PM
RE: New 18X - by Michael Gerber - 06-30-2012, 08:52 PM
RE: New 18 - by TA Forbes - 07-02-2012, 04:59 PM
RE: New 18 - by Philament - 07-02-2012, 09:03 PM
RE: New 18 - by codefox1 - 07-03-2012, 11:38 AM
RE: New 18 - by Philament - 07-13-2012, 10:50 AM
RE: New 18 - by jerryhawthorne - 07-13-2012, 10:04 PM
RE: New 18 - by codefox1 - 07-13-2012, 10:25 PM
RE: New 18 - by Philament - 07-13-2012, 10:46 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM
Philco model 38 code 121 not receiving signal.
Thankyou for the kind words sir. I double checked it with my component tester and it read 2.7 ohms at .02mH.Stormlord5500 — 08:14 AM

[-]
Who's Online
There are currently 2731 online users. [Complete List]
» 3 Member(s) | 2728 Guest(s)
AvatarAvatarAvatar

>