Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Identification
#7

Hi Rita and Welcome to the Phourm!
To answer your question it was produced in 1933 and 34 according to Ron's gallery. After looking at the pics/links Ron posted which one do you have? What some of plans do you have for it?
Agree with TA that it's good performer and has Good SW coverage as it tunes form the AM broadcast band to 18 MC. There's a lot of foreign broadcast from about 5MC up to the 18MC.
As CF sez if it hasn't been serviced in the last 10 or 15yrs it's probably due for a good going over. Without this if you try to use it you could easily damage the set and make it harder and more costly to repair.
Good Luck
Terry
ps Never clean a Philco dial (the orange/yellow part with the printing on it) with ANYTHING but odorless mineral spirits (OMS). Anything any WILL take the printing right off GONE FOREVER! Don't ask me how I know


Messages In This Thread
Identification - by Lane - 07-25-2012, 09:59 AM
RE: Identification - by codefox1 - 07-25-2012, 11:11 AM
RE: Identification - by Chuck Schwark - 07-25-2012, 11:37 AM
RE: Identification - by Ron Ramirez - 07-25-2012, 11:41 AM
RE: Identification - by TA Forbes - 07-25-2012, 02:52 PM
RE: Identification - by Steve Davis - 07-25-2012, 06:20 PM
RE: Identification - by 7estatdef - 07-25-2012, 09:27 PM
RE: Identification - by TA Forbes - 07-25-2012, 09:44 PM
RE: Identification - by Lane - 07-27-2012, 08:06 AM
RE: Identification - by Arran - 07-28-2012, 01:13 AM
RE: Identification - by codefox1 - 07-28-2012, 12:06 PM
RE: Identification - by 7estatdef - 07-28-2012, 05:51 PM
RE: Identification - by Lane - 07-28-2012, 09:32 PM
RE: Identification - by Ron Ramirez - 07-29-2012, 06:58 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 718 online users. [Complete List]
» 1 Member(s) | 717 Guest(s)
Avatar

>