Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Feedback for 42 355T
#4

The push pull setup these sets had was mostly for improving fidelity and reducing harmonic distortion, not for output power. I think that the undistorted power output is 5 watts or under, the plate and screen grids are running at a B+ of 180 volts, and not having a proper phase invertor also impeads power output. It's more then adequate for a table radio with a 5 or 6 inch speaker though. Reproduction plastic escutcheons are available from a few sources, Larry Bordanaro being one of them, make sure you get the 1942 escutcheon and not the 1941 version, you may need the pushbuttons as well.
Regards
Arran


Messages In This Thread
Feedback for 42 355T - by Paul Philco322 - 07-27-2012, 09:49 PM
RE: Feedback for 42 355T - by Arran - 07-28-2012, 12:43 AM
RE: Feedback for 42 355T - by Paul Philco322 - 07-29-2012, 08:49 PM
RE: Feedback for 42 355T - by Arran - 07-29-2012, 10:17 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 769 online users. [Complete List]
» 1 Member(s) | 768 Guest(s)
Avatar

>