Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

philco model 16
#13

then the wire at this junction goes off to the speaker plug ( going right ) toward floor of chaissis , it would also connect to resister 81 ( the silver one toward bottom pf your photo , then the other side goes to cap 73 on mine a mallory replacement 10 microfarad i think ( they grounded this replacment part to around bakelite cap 71 at it's screw ) then the other side goes across to 37 on my top of radio the shadow tower was broke of we reattached it , two wires have nothing i think shadow tuner lamp no bulb or scket, two other loose wires must be power for the lamp and shadow area. your wires look all new , our wires could be better around top of if cans


Messages In This Thread
philco model 16 - by ckc - 04-29-2007, 08:13 AM
[No subject] - by Chuck Schwark - 04-29-2007, 11:26 AM
[No subject] - by ckc - 04-29-2007, 01:03 PM
[No subject] - by Chuck Schwark - 04-29-2007, 02:47 PM
[No subject] - by ckc - 04-29-2007, 04:27 PM
[No subject] - by ckc - 04-29-2007, 05:14 PM
[No subject] - by Sean - 04-30-2007, 08:09 AM
[No subject] - by Sean - 04-30-2007, 09:14 PM
[No subject] - by ckc - 05-02-2007, 07:34 PM
[No subject] - by Sean - 05-03-2007, 08:21 AM
[No subject] - by ckc - 05-03-2007, 03:49 PM
[No subject] - by Sean - 05-03-2007, 05:10 PM
[No subject] - by ckc - 05-03-2007, 06:45 PM
[No subject] - by Sean - 05-04-2007, 08:43 AM
[No subject] - by ckc - 05-09-2007, 05:08 PM
[No subject] - by Sean - 05-09-2007, 05:14 PM
[No subject] - by ckc - 05-09-2007, 05:42 PM
[No subject] - by Sean - 05-10-2007, 08:09 AM
[No subject] - by ckc - 05-11-2007, 10:32 PM
[No subject] - by Sean - 05-12-2007, 08:16 PM
[No subject] - by ckc - 05-16-2007, 11:55 AM
[No subject] - by ckc - 05-18-2007, 05:20 PM
[No subject] - by ckc - 05-18-2007, 05:41 PM
[No subject] - by Sean - 05-19-2007, 08:26 PM
[No subject] - by ckc - 05-28-2007, 02:52 PM
[No subject] - by Sean - 05-28-2007, 05:37 PM
[No subject] - by ckc - 06-01-2007, 11:40 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 731 online users. [Complete List]
» 1 Member(s) | 730 Guest(s)
Avatar

>