New here w/q's re: Replacing '66 car radio pushbuttons

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

New here w/q's re: Replacing '66 car radio pushbuttons

Guest
Unregistered

05-12-2007, 01:25 AM

Hi Everyone, I'm new to the Phorum and glad to be here.

I have a couple of questions about a Philco model 6TPZ vintage am car radio cabinet restoration. First of all can anyone tell me how to remove the plastic pushbuttons for replacement? I've tried to pry them off but I'm afraid I might damage the shafts they're attached to. Also are these pushbuttons still available anywhere? Also are the bullet connectors for these vintage car radios still available and where? Any advice and help would be appreciated.

Thanks !

Steve

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

New here w/q's re: Replacing '66 car radio pushbuttons - by Guest - 05-12-2007, 01:25 AM

[No subject] - by Ron Ramirez - 05-13-2007, 02:18 PM

[No subject] - by BILL - 05-16-2007, 11:10 AM

[No subject] - by Guest - 05-16-2007, 11:27 AM

[No subject] - by BILL - 05-17-2007, 12:12 PM

[No subject] - by Guest - 05-17-2007, 01:55 PM

[No subject] - by Guest - 05-17-2007, 01:56 PM

[No subject] - by BILL - 05-25-2007, 05:30 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

Who's Online

There are currently 2183 online users. [Complete List]
» 1 Member(s) | 2182 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me