1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
A Beginner's Journey: The Philco 40-190
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#94

08-23-2012, 11:50 PM
Deck Ape, I have replaced a couple of those dang sockets, not nearly as much as some of the experts but a nice pan head screw coming down from the top or a nylon screw and a nylon nut on the bottom as they get a little close to HV underneath. Most I have done were on rectifier sockets. I find the hardware at ACE.
Jerry
A friend in need is a pest!  Bill Slee ca 1970.
(This post was last modified: 08-23-2012, 11:51 PM by jerryhawthorne.)
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
RE: A Beginner's Journey: The Philco 40-190 - by jerryhawthorne - 08-23-2012, 11:50 PM
[No subject] - by DeckApe - 07-07-2008, 03:39 PM
[No subject] - by Ron Ramirez - 07-07-2008, 09:45 PM
[No subject] - by DeckApe - 07-08-2008, 07:27 PM
[No subject] - by Michael Dennis - 07-08-2008, 10:14 PM
[No subject] - by DeckApe - 07-09-2008, 12:24 AM
[No subject] - by Michael Dennis - 07-09-2008, 07:05 AM
[No subject] - by DeckApe - 07-17-2008, 12:46 AM
[No subject] - by gary rabbitt - 07-17-2008, 03:04 AM
[No subject] - by DeckApe - 07-17-2008, 11:57 AM
[No subject] - by DeckApe - 07-18-2008, 11:28 PM
[No subject] - by DeckApe - 07-21-2008, 12:38 PM
[No subject] - by DeckApe - 07-24-2008, 11:17 PM
[No subject] - by DeckApe - 07-27-2008, 09:29 PM
[No subject] - by DeckApe - 07-29-2008, 01:16 AM
[No subject] - by BDM - 07-29-2008, 08:56 AM
[No subject] - by DeckApe - 07-29-2008, 12:20 PM
[No subject] - by DeckApe - 08-14-2008, 01:09 AM
[No subject] - by DeckApe - 08-14-2008, 11:48 AM
[No subject] - by Ron Ramirez - 08-14-2008, 10:37 PM
[No subject] - by DeckApe - 08-15-2008, 08:04 AM
[No subject] - by Ron Ramirez - 08-15-2008, 05:30 PM
[No subject] - by DeckApe - 08-16-2008, 03:38 PM
[No subject] - by Ron Ramirez - 08-16-2008, 04:17 PM
[No subject] - by DeckApe - 08-16-2008, 05:02 PM
[No subject] - by DeckApe - 08-21-2008, 01:08 AM
Re: - by Chuck Schwark - 09-07-2008, 10:49 PM
Re: A Beginner's Journey: The Philco 40-190 - by Guest - 09-16-2008, 08:30 PM
Re: A Beginner's Journey: The Philco 40-190 - by Guest - 03-28-2010, 04:08 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
So what was wrong with the original speaker? Was the cone damaged? Unless it's totally hopeless I would put it aside as ...Arran — 05:31 PM
My collection presentation
There is an article on my site that introduces the first portable radios in my collection. I have only provided a link t...Vlad95 — 01:17 PM
Electrolytic restuffing/internals
Bridkarl This specific cap you have is the easiset type to restuff. I usually cut it at the upper border of the depr...morzh — 11:35 AM
philco predicta
Hi CGL18, First off, welcome to the Philco Phorum. I have not worked on a TV for a while but here are some givens: ...MrFixr55 — 08:22 AM
Another amp build - here I go again!
Sweet! I actually have a Dynaco Mark 4 that I had been running with 6L6s with no mods. Seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration