1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
How to identify and choose veneer
Arran
Phorum Expert
*****
Posts: 4,894
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
#2

09-24-2012, 05:39 PM
Mars,
I think I mentioned what the species of veneer was in the thread you started about stripping the cabinet. In any event the veneer that was used on the control panel/top of your radio was plain cut French walnut, same with the veneer on the shoulders. As far as I know they did not use black walnut on these cabinets, though some manufacturers did. As for suppliers there are several out there, I bought mine from a fellow on fleabay about a year ago, along with a bunch of other veneer species and cuts. Albert Constantine has many species of veneer, so does Rockler Woodworking, but there are others.
Regards
Arran
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
How to identify and choose veneer - by Marsupial - 09-24-2012, 01:05 PM
RE: How to identify and choose veneer - by Arran - 09-24-2012, 05:39 PM
RE: How to identify and choose veneer - by Arran - 09-25-2012, 08:14 PM
RE: How to identify and choose veneer - by Arran - 09-25-2012, 10:14 PM
RE: How to identify and choose veneer - by Arran - 09-29-2012, 12:41 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2255 online users. [Complete List]
» 5 Member(s) | 2250 Guest(s)
AvatarAvatarAvatarAvatar
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration