Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 111 cabinet question final pics!
#26

Well, done and playing nicely. Thought I would post a couple of pictures. Still missing the label on the top of the tube shield which no one apparently has one they could shoot a picture of.
I did refinish the top as I could not get the water ring to look right. The rest of the cabinet other than the very bottom of the legs is original. The bottom of the legs were pretty beat up, perhaps by a vacuum cleaner bumping into them for many years.
The old girl shows some bumps and grinds but is original for the most part, with just some cleaning and a little wax.
Thank you all for your suggestions.
Jerry

[Image: http://i303.photobucket.com/albums/nn129...11done.jpg]

[Image: http://i303.photobucket.com/albums/nn129...1done1.jpg]

A friend in need is a pest!  Bill Slee ca 1970.


Messages In This Thread
RE: Philco 111 cabinet question - by Phlogiston - 08-05-2012, 05:25 PM
RE: Philco 111 cabinet question - by TA Forbes - 08-05-2012, 08:41 PM
RE: Philco 111 cabinet question - by codefox1 - 08-05-2012, 09:49 PM
RE: Philco 111 cabinet question - by Phlogiston - 08-06-2012, 01:29 AM
RE: Philco 111 cabinet question - by TA Forbes - 08-06-2012, 10:19 PM
RE: Philco 111 cabinet question - by codefox1 - 08-10-2012, 02:13 PM
RE: Philco 111 cabinet question - by TA Forbes - 08-12-2012, 04:12 AM
RE: Philco 111 cabinet question - by codefox1 - 09-14-2012, 07:41 PM
RE: Philco 111 cabinet question - by codefox1 - 09-14-2012, 08:03 PM
RE: Philco 111 cabinet question - by TA Forbes - 09-15-2012, 12:36 AM
RE: Philco 111 cabinet question - by TA Forbes - 09-19-2012, 09:04 PM
RE: Philco 111 cabinet question - by TA Forbes - 09-19-2012, 10:15 PM
RE: Philco 111 cabinet question - by TA Forbes - 09-20-2012, 01:57 PM
RE: Philco 111 cabinet question - by TA Forbes - 09-30-2012, 12:15 AM
RE: Philco 111 cabinet question - by jerryhawthorne - 10-03-2012, 06:46 PM



Users browsing this thread:
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2280 online users. [Complete List]
» 4 Member(s) | 2276 Guest(s)
AvatarAvatarAvatarAvatar

>