Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Another Grill Cloth Question
#4

I contacted a company in Wisconcin who manufacture specialty cloth, they emailed me back saying that they would be willing to reproduce cloth to the best of their ability.

"Please send me what samples you might have (I'd return them, of course) as well as any links or information regarding the materials used in these fabrics.
Reproducing a pattern is not that difficult, but often the yarns used were odd blends of natural and synthetic materials that are difficult to duplicate.
I could probably give you some idea of what you'd need in terms of textile terms, etc. and possibly offer to make some for you or refer your request to someone who can.
Our mailing address is The Woolgatherers, 25-A N. Main St., Fond du Lac, WI 54935.
Sara von Tresckow, Fond du Lac, WI
sarav@woolgatherers.com"

http://www.woolgatherers.com

I plan to go this route, and I hope the information will help you guys as well.


Messages In This Thread
RE: Another Grill Cloth Question - by Arran - 11-15-2012, 11:20 PM
RE: Another Grill Cloth Question - by TheFightingHellfish - 11-17-2012, 07:14 PM
RE: Another Grill Cloth Question - by Arran - 11-18-2012, 02:37 AM
RE: Another Grill Cloth Question - by TA Forbes - 11-19-2012, 02:58 PM
RE: Another Grill Cloth Question - by Ron Ramirez - 11-19-2012, 03:22 PM
RE: Another Grill Cloth Question - by Phlogiston - 11-19-2012, 08:53 PM
RE: Another Grill Cloth Question - by Dick Finn - 11-20-2012, 11:21 AM
RE: Another Grill Cloth Question - by codefox1 - 11-20-2012, 01:42 PM
RE: Another Grill Cloth Question - by Dick Finn - 11-20-2012, 05:25 PM
RE: Another Grill Cloth Question - by LASJayhawk - 11-25-2012, 01:42 PM
RE: Another Grill Cloth Question - by Arran - 11-25-2012, 10:05 PM
RE: Another Grill Cloth Question - by Arran - 11-26-2012, 02:10 AM
RE: Another Grill Cloth Question - by TheGorper - 12-31-2012, 11:49 PM
RE: Another Grill Cloth Question - by Ron Ramirez - 01-01-2013, 12:07 AM
RE: Another Grill Cloth Question - by Art Hoch - 03-29-2013, 09:31 PM
RE: Another Grill Cloth Question - by LASJayhawk - 05-11-2013, 03:42 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 698 online users. [Complete List]
» 1 Member(s) | 697 Guest(s)
Avatar

>