1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco Model 66 Repair
Radioroslyn
Phorum Expert
*****
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
#2

11-21-2012, 06:07 PM
Well the best thing to do if you think the osc isn't running is to mark and then unsolder the wires on the coil. Remove it measure each winding with all rest of the radio connected to it. That way you will get an accurate reading. All of the windings should if good show a low resistance like 100 ohms of lower.
GL
Terry
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco Model 66 Repair - by radiola - 11-21-2012, 12:43 AM
RE: Philco Model 66 Repair - by 7estatdef - 11-21-2012, 06:07 PM
RE: Philco Model 66 Repair - by jph14 - 11-21-2012, 07:53 PM
RE: Philco Model 66 Repair - by radiola - 11-21-2012, 08:00 PM
RE: Philco Model 66 Repair - by 7estatdef - 11-21-2012, 10:08 PM
RE: Philco Model 66 Repair - by TA Forbes - 11-21-2012, 10:25 PM
RE: Philco Model 66 Repair - by radiola - 11-21-2012, 11:10 PM
RE: Philco Model 66 Repair - by 7estatdef - 11-22-2012, 12:58 AM
RE: Philco Model 66 Repair - by radiola - 11-23-2012, 10:12 PM
RE: Philco Model 66 Repair - by 7estatdef - 11-25-2012, 05:39 PM
RE: Philco Model 66 Repair - by radiola - 11-25-2012, 06:20 PM
RE: Philco Model 66 Repair - by jerryhawthorne - 11-25-2012, 09:30 PM
RE: Philco Model 66 Repair - by radiola - 11-25-2012, 10:48 PM
RE: Philco Model 66 Repair - by 7estatdef - 11-25-2012, 11:21 PM
RE: Philco Model 66 Repair - by radiola - 11-26-2012, 10:01 PM
RE: Philco Model 66 Repair - by 7estatdef - 11-27-2012, 12:16 AM
RE: Philco Model 66 Repair - by radiola - 11-27-2012, 01:12 AM
RE: Philco Model 66 Repair - by 7estatdef - 11-27-2012, 11:20 PM
RE: Philco Model 66 Repair - by TA Forbes - 11-27-2012, 11:47 PM
RE: Philco Model 66 Repair - by radiola - 11-28-2012, 12:34 AM
RE: Philco Model 66 Repair - by 7estatdef - 11-28-2012, 11:32 PM
RE: Philco Model 66 Repair - by radiola - 11-29-2012, 02:21 AM
RE: Philco Model 66 Repair - by 7estatdef - 11-29-2012, 10:30 PM
RE: Philco Model 66 Repair - by radiola - 11-30-2012, 02:32 AM
RE: Philco Model 66 Repair - by 7estatdef - 11-30-2012, 06:54 PM
RE: Philco Model 66 Repair - by radiola - 11-30-2012, 11:30 PM
RE: Philco Model 66 Repair - by 7estatdef - 12-01-2012, 06:51 PM
RE: Philco Model 66 Repair - by radiola - 12-02-2012, 10:41 PM
RE: Philco Model 66 Repair - by 7estatdef - 12-02-2012, 10:53 PM
RE: Philco Model 66 Repair - by 7estatdef - 12-04-2012, 11:00 PM
RE: Philco Model 66 Repair - by radiola - 12-05-2012, 12:52 AM



Users browsing this thread:
[-]
Recent Posts
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM
Philco model 38 code 121 not receiving signal.
Thankyou for the kind words sir. I double checked it with my component tester and it read 2.7 ohms at .02mH.Stormlord5500 — 08:14 AM

[-]
Who's Online
There are currently 2775 online users. [Complete List]
» 3 Member(s) | 2772 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration