1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Another Grill Cloth Question
Arran
Phorum Expert
*****
Posts: 4,894
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
#15

11-25-2012, 10:05 PM
Cloth is usually measured by the linear yard not the square yard, most rolls of fabric are 36 inches wide. So if it works out to $29 a linear yard then that is a figure that makes sense. One of the chevron patterned Philco cloths would be a good one to start with as you could produce and sell 20 or more yards easily. Another good one would be the cloth used in Philco 70 and 90 sets, because of the pattern used almost all of the 36'' width would be useful.
Regards
Arran
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
RE: Another Grill Cloth Question - by Arran - 11-15-2012, 11:20 PM
RE: Another Grill Cloth Question - by Arran - 11-18-2012, 02:37 AM
RE: Another Grill Cloth Question - by TA Forbes - 11-19-2012, 02:58 PM
RE: Another Grill Cloth Question - by Ron Ramirez - 11-19-2012, 03:22 PM
RE: Another Grill Cloth Question - by Phlogiston - 11-19-2012, 08:53 PM
RE: Another Grill Cloth Question - by Dick Finn - 11-20-2012, 11:21 AM
RE: Another Grill Cloth Question - by codefox1 - 11-20-2012, 01:42 PM
RE: Another Grill Cloth Question - by Dick Finn - 11-20-2012, 05:25 PM
RE: Another Grill Cloth Question - by LASJayhawk - 11-25-2012, 01:42 PM
RE: Another Grill Cloth Question - by Arran - 11-25-2012, 10:05 PM
RE: Another Grill Cloth Question - by Arran - 11-26-2012, 02:10 AM
RE: Another Grill Cloth Question - by TheGorper - 12-31-2012, 11:49 PM
RE: Another Grill Cloth Question - by Ron Ramirez - 01-01-2013, 12:07 AM
RE: Another Grill Cloth Question - by Art Hoch - 03-29-2013, 09:31 PM
RE: Another Grill Cloth Question - by LASJayhawk - 05-11-2013, 03:42 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 701 online users. [Complete List]
» 1 Member(s) | 700 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration