Philco Model 66 Repair

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco Model 66 Repair

radiola
Member

Posts: 64
Threads: 10
Joined: Dec 2010
City: Baltimore, MD

#20

11-28-2012, 12:34 AM

Coil side of resistor 10 to 800 pf (side connected to pin 4 of 6A7) 214 K

Coil side of resistor 10 to 800 pf that is connected to the coil. 64 ohms

Just making sure we're on the same page. Line one above describes coil side of resistor 10 to 800 pf which is not the coil side, but the reading is picked up at pin 4 of the 6A7.

Line two describes basicly resistance of one oscillator coil lug to the other.

So, is it a proper reading to test the resistor, coil side and pin 4 after it has gone through a mica cap??

Sorry, just want to make sure we're on the same page.
Much appreciated !!

By the way, resistor #15 is 32.95 K, well within spec of 32 k. Sorry.

(This post was last modified: 11-28-2012, 12:47 AM by radiola.)

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Philco Model 66 Repair - by radiola - 11-21-2012, 12:43 AM

RE: Philco Model 66 Repair - by 7estatdef - 11-21-2012, 06:07 PM

RE: Philco Model 66 Repair - by jph14 - 11-21-2012, 07:53 PM

RE: Philco Model 66 Repair - by radiola - 11-21-2012, 08:00 PM

RE: Philco Model 66 Repair - by 7estatdef - 11-21-2012, 10:08 PM

RE: Philco Model 66 Repair - by TA Forbes - 11-21-2012, 10:25 PM

RE: Philco Model 66 Repair - by radiola - 11-21-2012, 11:10 PM

RE: Philco Model 66 Repair - by 7estatdef - 11-22-2012, 12:58 AM

RE: Philco Model 66 Repair - by radiola - 11-23-2012, 10:12 PM

RE: Philco Model 66 Repair - by 7estatdef - 11-25-2012, 05:39 PM

RE: Philco Model 66 Repair - by radiola - 11-25-2012, 06:20 PM

RE: Philco Model 66 Repair - by jerryhawthorne - 11-25-2012, 09:30 PM

RE: Philco Model 66 Repair - by radiola - 11-25-2012, 10:48 PM

RE: Philco Model 66 Repair - by 7estatdef - 11-25-2012, 11:21 PM

RE: Philco Model 66 Repair - by radiola - 11-26-2012, 10:01 PM

RE: Philco Model 66 Repair - by 7estatdef - 11-27-2012, 12:16 AM

RE: Philco Model 66 Repair - by radiola - 11-27-2012, 01:12 AM

RE: Philco Model 66 Repair - by 7estatdef - 11-27-2012, 11:20 PM

RE: Philco Model 66 Repair - by TA Forbes - 11-27-2012, 11:47 PM

RE: Philco Model 66 Repair - by radiola - 11-28-2012, 12:34 AM

RE: Philco Model 66 Repair - by 7estatdef - 11-28-2012, 11:32 PM

RE: Philco Model 66 Repair - by radiola - 11-29-2012, 02:21 AM

RE: Philco Model 66 Repair - by 7estatdef - 11-29-2012, 10:30 PM

RE: Philco Model 66 Repair - by radiola - 11-30-2012, 02:32 AM

RE: Philco Model 66 Repair - by 7estatdef - 11-30-2012, 06:54 PM

RE: Philco Model 66 Repair - by radiola - 11-30-2012, 11:30 PM

RE: Philco Model 66 Repair - by 7estatdef - 12-01-2012, 06:51 PM

RE: Philco Model 66 Repair - by radiola - 12-02-2012, 10:41 PM

RE: Philco Model 66 Repair - by 7estatdef - 12-02-2012, 10:53 PM

RE: Philco Model 66 Repair - by 7estatdef - 12-04-2012, 11:00 PM

RE: Philco Model 66 Repair - by radiola - 12-05-2012, 12:52 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM
Philco model 38 code 121 not receiving signal.
Thankyou for the kind words sir. I double checked it with my component tester and it read 2.7 ohms at .02mH.Stormlord5500 — 08:14 AM

Who's Online

There are currently 2770 online users. [Complete List]
» 3 Member(s) | 2767 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me