Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Parts for Philco 42-365-- what is this called?
#1

Hello. I am new to this forum. Although I have owned my radio since 1977, because it has played just fine, I never learned much about it. I have never been technologically savvy. I have just enjoyed my radio as it is but since we have recently moved into a new house, the radio seems to have been jarred in transit, and no longer fits securely in the cabinet.

I believe I need a few parts for my radio -- and I don't know what these little rubber blocks are called. Maybe someone can help me? They are on either side of the radio, which is seated on the shelf of the cabinet. They are on either side and appear to secure the radio in place. One is missing and the other is deteriorating.

Perhaps if the radio were positioned more securely, I could use the push buttons better (they seem to be connected to nothing -- but the dial works....albeit backwards). When I push the buttons, the entire radio seems to move in tghe cabinet.

The dial has been backwards since my ex-husband put it together back in the seventies.

I would also like to buy some knobs. I have four bakelite ones which fit loosely, but I am a hoarder and so would like the security of owning extras.

I found the Philco Phorum when I decided to have my Philco 42-365 repaired (the dial seems to be backwards -- 55krc is where wcky 1630 should be) and wanted to purchase specs.


The price for Ron's radio repair doesn't faze me....I just could not ship it. I would be a wreck! I would sooner drive it to Evansville, but I would have to recruit my husband for that and I don't think he will do it in this lifetime.

Thank you.

Sincerely,

Buffy in Cincinnati


Messages In This Thread
Parts for Philco 42-365-- what is this called? - by Guest - 08-06-2007, 02:50 PM
[No subject] - by Ron Ramirez - 08-06-2007, 10:15 PM
[No subject] - by Guest - 08-07-2007, 06:06 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>