Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 50 in Combs Cabinet
#3

That's fine, Ron, thanks. The only reason I knew about it was when I was going through your gallery, VERY nice job!! I read you short bit about the Baby Grand Model 50, and how uncommon the Combs cabinet is with this model. I remembered that when I saw this Model 50, and I'm going to try for it. The cabinet is a little beat up, but, nothing chronic, and the chassis has some surface rust, but, it looks like it's all there. This is an A/C TRF like the Model 20, right? How different are the tubes between the two? I have a plain Model 20, as well as a Baby Grand Model 70, love them both!! I want to add to the growing Philco collection, maybe, I'll surpass the Zeniths I have in number, LOL Icon_wink ! Thanks for this site and all the work you've done for the hobby!! I've only been into this hobby a few years, but, I've known about the "Philco Orical", you!! I've spent hours looking and researching my two Philcos on your site, so, it means alot to have all of this info in one place! Have a great weekend!!

Jerry


Messages In This Thread
Model 50 in Combs Cabinet - by Guest - 08-11-2007, 02:10 PM
[No subject] - by Ron Ramirez - 08-11-2007, 02:42 PM
[No subject] - by Guest - 08-11-2007, 07:14 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>