1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Another resistor ID needed/RESOLVED
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#11

01-16-2013, 03:22 PM
DK:
I'm self taught. 25 years in USMC grunt and Recon units did not afford me much in electronic education, although it did give me a good education in shortwave propagation. BUT I had an innate sense of what I knew and did not know, and how and where to go to learn what I did not know.

My point is, you get smarter by finding "real deal" radio-men and being worthy of their company. AND read! There is a wealth of stuff out there that helps rock-apes like me learn how to be better at radios.

We ALL asked dum questions early in our radio-hobby adventure. ALL of us!!!

AND your questions are neither dumb nor are they tedious. Do continue to ask them!!

This site is an excellent source for knowledge. Keep coming back, and keep asking the questions!!
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
RE: Another resistor ID needed - by TA Forbes - 01-14-2013, 09:56 PM
RE: Another resistor ID needed - by DKinYORKpa - 01-14-2013, 10:16 PM
RE: Another resistor ID needed - by TA Forbes - 01-15-2013, 11:25 PM
RE: Another resistor ID needed - by DKinYORKpa - 01-16-2013, 08:55 AM
RE: Another resistor ID needed - by Ron Ramirez - 01-16-2013, 10:28 AM
RE: Another resistor ID needed - by codefox1 - 01-16-2013, 01:50 PM
RE: Another resistor ID needed - by DKinYORKpa - 01-16-2013, 02:15 PM
RE: Another resistor ID needed - by Ron Ramirez - 01-16-2013, 02:29 PM
RE: Another resistor ID needed - by DKinYORKpa - 01-16-2013, 02:57 PM
RE: Another resistor ID needed - by TA Forbes - 01-16-2013, 03:22 PM
RE: Another resistor ID needed - by DKinYORKpa - 01-23-2013, 02:54 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM
Philco model 38 code 121 not receiving signal.
Thankyou for the kind words sir. I double checked it with my component tester and it read 2.7 ohms at .02mH.Stormlord5500 — 08:14 AM
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM

[-]
Who's Online
There are currently 1063 online users. [Complete List]
» 1 Member(s) | 1062 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration