1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Starting on a Model 20
GarySP
Super Moderator
******
Posts: 2,159
Threads: 158
Joined: Jan 2013
City: Westland, MI
#5

01-18-2013, 02:46 PM
Thanks for the bulb info Ron. I'll pick that up when I go to get my caps. I'm lucky enough to still have an electronics parts store just a couple of miles away from my house. They are truly going by the wayside. The owner says he might even have some NOS tubes I might need...he just has to dig through his very dusty inventory. Says he has two Hickok tube testers, but isn't really ready to part with them. I'll keep trying. On another note, I have an issue with a warped dial indicator. Any clues as to how I might be able to straighten it? It is in very good shape other than the warp. Thanks again for all the help. Gary
"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Starting on a Model 20 - by GarySP - 01-17-2013, 04:10 PM
RE: Starting on a Model 20 - by TA Forbes - 01-18-2013, 01:38 AM
RE: Starting on a Model 20 - by GarySP - 01-18-2013, 09:23 AM
RE: Starting on a Model 20 - by Ron Ramirez - 01-18-2013, 12:54 PM
RE: Starting on a Model 20 - by GarySP - 01-18-2013, 02:46 PM
RE: Starting on a Model 20 - by TA Forbes - 01-18-2013, 09:35 PM
RE: Starting on a Model 20 - by GarySP - 01-20-2013, 10:11 PM
RE: Starting on a Model 20 - by GarySP - 01-21-2013, 12:07 PM
RE: Starting on a Model 20 - by GarySP - 01-24-2013, 10:31 PM
RE: Starting on a Model 20 - by TA Forbes - 01-25-2013, 12:48 AM
RE: Starting on a Model 20 - by Joe - 01-26-2013, 11:53 AM
RE: Starting on a Model 20 - by GarySP - 01-29-2013, 11:38 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 759 online users. [Complete List]
» 1 Member(s) | 758 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration