1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Could someone pat me on the back?
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#20

02-12-2013, 12:29 PM
DKinYORKpa Wrote:The one 45 tests almost GOOD and the other one is down in the BAD. Does that explain why the one tube, while lit, is practically cold while the other one is hot?

Not necessarily. Check your audio output transformer. If one of the output tubes remains cold, I would suspect one half of the primary winding may be bad.

I'm not saying it couldn't be the tube because it certainly could be - but do check that audio output transformer before proceeding.
--
Ron Ramirez
Ferdinand IN
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Could someone pat me on the back? - by DKinYORKpa - 02-10-2013, 12:25 PM
RE: Could someone pat me on the back? - by Eric T - 02-10-2013, 03:39 PM
RE: Could someone pat me on the back? - by morzh - 02-10-2013, 04:55 PM
RE: Could someone pat me on the back? - by Arran - 02-10-2013, 07:48 PM
RE: Could someone pat me on the back? - by morzh - 02-10-2013, 10:46 PM
RE: Could someone pat me on the back? - by FXpert - 02-11-2013, 07:13 AM
RE: Could someone pat me on the back? - by morzh - 02-12-2013, 12:14 AM
RE: Could someone pat me on the back? - by Ron Ramirez - 02-12-2013, 12:29 PM
RE: Could someone pat me on the back? - by morzh - 02-14-2013, 08:56 PM
RE: Could someone pat me on the back? - by morzh - 02-15-2013, 08:34 PM



Users browsing this thread:
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently 954 online users. [Complete List]
» 2 Member(s) | 952 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration