1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
49-500 alignment procedure
N6MKC
Junior Member
**
Posts: 11
Threads: 6
Joined: Feb 2013
City: Camino, CA
#1

03-09-2013, 01:51 AM
Just finished restoring a 49-500 I picked up from a craigslist ad sometime back for $10. The thing was filthy, filthy, filthy, complete with rodent droppings, and urine stains on the chassis. It took a ton of labor and elbow-grease, but the cabinet and chassis cleaned up very nicely. New caps, a few new resistors, and she's almost back to life. I checked out the Riders alignment procedure, and there's a significant chunk of the page that's cutoff. I've downloaded all of the free copies available online, but they're all of unacceptable quality, with the same missing pieces. Can anybody set me up with a legible copy of the procedure?
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
49-500 alignment procedure - by N6MKC - 03-09-2013, 01:51 AM
RE: 49-500 alignment procedure - by klondike98 - 03-09-2013, 11:09 AM
RE: 49-500 alignment procedure - by N6MKC - 03-09-2013, 03:16 PM



Users browsing this thread:
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2182 online users. [Complete List]
» 1 Member(s) | 2181 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration