Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

37-650, What do you think?
#8

Mine is a 630 but very close to the same finish.
This is out in the sunset, so it is a little darker in a room:

   

   

Your "refinisher" should be painting houses.

That one could still be fixed. It would not be too hard for someone that knows how. Maybe you need an amateur.


Messages In This Thread
37-650, What do you think? - by Guest - 06-13-2010, 05:45 PM
RE: 37-650, What do you think? - by Phlogiston - 03-10-2013, 01:29 AM
RE: 37-650, What do you think? - by ipwizard - 03-14-2013, 03:30 PM
RE: 37-650, What do you think? - by Tom Hamilton - 03-24-2013, 01:33 PM
Re: 37-650, What do you think? - by Ron Ramirez - 06-13-2010, 08:04 PM
Re: 37-650, What do you think? - by Guest - 06-13-2010, 10:33 PM
Re: 37-650, What do you think? - by hotrod - 06-17-2010, 02:16 AM
Re: 37-650, What do you think? - by Guest - 06-20-2010, 10:26 AM
Re: 37-650, What do you think? - by Ron Ramirez - 06-23-2010, 03:03 PM
Re: 37-650, What do you think? - by Arran - 08-28-2010, 09:53 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 752 online users. [Complete List]
» 1 Member(s) | 751 Guest(s)
Avatar

>