It's Alive!!!

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

It's Alive!!!

Mr Grumpy
Junior Member

Posts: 45
Threads: 8
Joined: Jan 2013
City: Toronto Ontario

#22

03-23-2013, 10:01 PM

I'm going to keep my eyes peeled and my fingers crossed and hopefully I'll find one in the future.
for now I'll either put the geared motor back in or try and modify a motor and idler assembly to fit.

@Arran, Thanks for the additional info, I had no idea about the 25 cycle outside of Canada. Learn something new every time I log into this place!

(This post was last modified: 03-23-2013, 10:04 PM by Mr Grumpy.)

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

It's Alive!!! - by Mr Grumpy - 02-11-2013, 04:28 PM

RE: It's Alive!!! - by klondike98 - 02-11-2013, 05:09 PM

RE: It's Alive!!! - by Mr Grumpy - 02-12-2013, 01:21 PM

RE: It's Alive!!! - by jerryhawthorne - 02-12-2013, 01:35 PM

RE: It's Alive!!! - by marv - 02-12-2013, 04:37 PM

RE: It's Alive!!! - by jerryhawthorne - 02-12-2013, 05:58 PM

RE: It's Alive!!! - by Mr Grumpy - 02-13-2013, 12:23 AM

RE: It's Alive!!! - by Eric T - 02-14-2013, 10:20 PM

RE: It's Alive!!! - by jerryhawthorne - 02-14-2013, 10:31 PM

RE: It's Alive!!! - by wa2ise - 02-14-2013, 11:50 PM

RE: It's Alive!!! - by TA Forbes - 02-15-2013, 01:24 AM

RE: It's Alive!!! - by Mr Grumpy - 02-16-2013, 09:49 PM

RE: It's Alive!!! - by Mr Grumpy - 02-27-2013, 01:09 PM

RE: It's Alive!!! - by Mr Grumpy - 03-20-2013, 09:48 PM

RE: It's Alive!!! - by 7estatdef - 03-22-2013, 09:47 PM

RE: It's Alive!!! - by Mr Grumpy - 03-22-2013, 10:58 PM

RE: It's Alive!!! - by Arran - 03-22-2013, 11:18 PM

RE: It's Alive!!! - by Mr Grumpy - 03-22-2013, 11:55 PM

RE: It's Alive!!! - by Arran - 03-23-2013, 03:18 AM

RE: It's Alive!!! - by Steve Davis - 03-23-2013, 02:27 PM

RE: It's Alive!!! - by 7estatdef - 03-23-2013, 06:19 PM

RE: It's Alive!!! - by Mr Grumpy - 03-23-2013, 10:01 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

Who's Online

There are currently 2222 online users. [Complete List]
» 2 Member(s) | 2220 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me