Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

Philco 41-296 Troubles
#1

[Hope I have posted this in the proper place]

I am restoring the chassis on this radio and have replaced all caps (except micas for now), and most all resistors. Those I have not replaced were well within spec.

I aligned the IF with no issues, however I am not able to hear the fundamental at 1500kcs or 550kcs from my signal generator no matter where I adjust 16 and 17. I have heard, what I think is a harmonic, and if I spot it on 1500kcs, I hear no stations in the BC band. However, I can detune 16 and hear BC stations, but they are very broad, like 100kcs+, so something is obviously amiss.

Assuming everything else is correct, Osc transformer (checked), etc., what should I be looking for. Only mica cap I've found way off is 4, which reads about 105pf and should be about 250pf. Currently don't have one to replace it with. I have also checked all the IF transformers and found them to be right in spec., no open windings, etc.

Another odd thing was a wire installed on the antenna coil wrapped at both ends connected to, I think, 7 and 5 taps. I am assuming it was a "gimick cap" for something. I removed it, however not knowing what it was for, should I replace it? At first I thought it was not original, but I read somewhere else that someone else found this in his 41-296. Photo attached.

Any suggestions would be greatly appreciated. I am not an expert tech by any means, so forgive me if I've left out any important points.

Thanks
Brian


Messages In This Thread
Philco 41-296 Troubles - by w5ami - 04-03-2013, 05:13 PM
RE: Philco 41-296 Troubles - by jerryhawthorne - 04-03-2013, 10:03 PM
RE: Philco 41-296 Troubles - by w5ami - 04-04-2013, 07:46 AM
RE: Philco 41-296 Troubles - by 7estatdef - 04-04-2013, 02:05 PM
RE: Philco 41-296 Troubles - by w5ami - 04-05-2013, 05:15 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
hello david, I have a similar generator in my collection that features a cast iron, single-cylinder Briggs & Stratt...radiorich — 01:00 AM
under chassis parts locator diagram for 1938 Zenith 9s262
Has anyone gone to the trouble of creating an under chassis parts locator image?  Yes, I can identify components by foll...bobloney — 08:57 PM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
Try looking at this site the book mark is for a old generator that I was given. David    https://radionerds.com/index.ph...David — 08:36 PM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
Hello Everyone, I am looking for voltage identification for all the pin positions on the socket of a CRV-20130 power su...Tonym4704 — 08:16 PM
Philco P45-6365 Universal Transformer Instruction Manual
Can anyone guide me to where this may be found?GRG — 03:00 PM
54C Complete Teardown/Rebuild
I don't think that I have encountered a 12Z3 before, curious how it uses one of those but includes a #43, which is a 25 ...Arran — 02:17 PM
HiFi (Chifi) tube amp build - but my own design.
It's the other forum. I'm also in DIY, but mostly read there. Honestly, I kinda jumped into this without much thought to...TV MAN — 10:43 AM
Philco 71 Code 125
Hello,  I am in need of a schematic for this radio. Mine has the three separate circular tube shields and a shadow me...dconant — 08:06 AM
Stromberg Carlson 1500 Squeal
And life just keeps getting more complicated.dconant — 07:57 AM
54C Complete Teardown/Rebuild
Hello Roy, here is this one sincerely Richardradiorich — 12:45 AM

[-]
Who's Online
There are currently 2236 online users. [Complete List]
» 1 Member(s) | 2235 Guest(s)
Avatar

>