1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Odd Heater String 116X
Radioroslyn
Phorum Expert
*****
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
#1

04-19-2013, 09:22 PM
Was looking over the diagram for my 116X and noticed that it uses a hum balance pot to null the 60cy AC on the directly heated output tubes (6A3's). This is a common practice with audio tubes that don't have a cathode. But wait. One of the 6A3's is tied across the pot and the driver tube heater and the RF tubes. The other 6A3 filament is tied across the IF amps,det,and 1st audio. It's filament winding has a ct which is grounded. Pretty Odd!!

http://www.nostalgiaair.org/PagesByModel...013123.pdf
Terry
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Odd Heater String 116X - by 7estatdef - 04-19-2013, 09:22 PM
RE: Odd Heater String 116X - by codefox1 - 04-20-2013, 03:54 AM
RE: Odd Heater String 116X - by Mondial - 04-20-2013, 08:48 AM
RE: Odd Heater String 116X - by ipwizard - 04-20-2013, 10:04 AM
RE: Odd Heater String 116X - by 7estatdef - 04-20-2013, 08:22 PM
RE: Odd Heater String 116X - by Mondial - 04-20-2013, 10:09 PM
RE: Odd Heater String 116X - by 7estatdef - 04-21-2013, 02:01 PM
RE: Odd Heater String 116X - by 7estatdef - 04-22-2013, 05:24 PM
RE: Odd Heater String 116X - by Mondial - 04-22-2013, 06:37 PM
RE: Odd Heater String 116X - by 7estatdef - 04-22-2013, 09:12 PM
RE: Odd Heater String 116X - by Mondial - 04-22-2013, 10:23 PM
RE: Odd Heater String 116X - by chris25260880 - 04-23-2013, 11:23 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently 944 online users. [Complete List]
» 2 Member(s) | 942 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration