Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

B&K RF Signal Generator Repair
#21

OK, Now you tell me. Icon_eek
Q3 - BE is open. All others check OK. I pulled them out before I saw your last post so I didn't check the power supply voltages.

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org



Messages In This Thread
B&K RF Signal Generator Repair - by Eric Adams - 05-09-2013, 07:53 PM
RE: B&K RF Signal Generator Repair - by morzh - 05-09-2013, 08:03 PM
RE: B&K RF Signal Generator Repair - by morzh - 05-09-2013, 09:11 PM
RE: B&K RF Signal Generator Repair - by morzh - 05-10-2013, 09:00 AM
RE: B&K RF Signal Generator Repair - by morzh - 05-10-2013, 02:56 PM
RE: B&K RF Signal Generator Repair - by morzh - 05-10-2013, 08:35 PM
RE: B&K RF Signal Generator Repair - by morzh - 05-10-2013, 08:37 PM
RE: B&K RF Signal Generator Repair - by Arran - 05-10-2013, 09:10 PM
RE: B&K RF Signal Generator Repair - by morzh - 05-11-2013, 07:36 PM
RE: B&K RF Signal Generator Repair - by morzh - 05-11-2013, 09:15 PM
RE: B&K RF Signal Generator Repair - by morzh - 05-11-2013, 10:36 PM
RE: B&K RF Signal Generator Repair - by Eric Adams - 05-11-2013, 10:44 PM
RE: B&K RF Signal Generator Repair - by morzh - 05-11-2013, 11:02 PM
RE: B&K RF Signal Generator Repair - by morzh - 05-11-2013, 11:16 PM
RE: B&K RF Signal Generator Repair - by morzh - 05-12-2013, 08:40 PM
RE: B&K RF Signal Generator Repair - by morzh - 05-13-2013, 12:23 PM
RE: B&K RF Signal Generator Repair - by morzh - 05-15-2013, 01:36 PM
RE: B&K RF Signal Generator Repair - by morzh - 05-15-2013, 02:49 PM
RE: B&K RF Signal Generator Repair - by morzh - 05-16-2013, 09:34 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>