using 12AU7 on 34

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

using 12AU7 on 34

marty
Member

Posts: 240
Threads: 27
Joined: Jun 2013
City: Boulder, Colorado

#15

06-30-2013, 10:39 PM

Hi All;
Mondial, Thank You for letting me know that I need to wait for the tube to come in..
Yes, I have checked all of the resistors, and have the replacements and I have two coils to go.. The others are fine.. At first look, none of the coils have that wire rott, that seems so prevelent in other sets..
I don't have a reliable cap checker, my friend has one, but may be awhile before I can have Him bring it over.. I do have the Replacement caps, except for two of them, but I can make them up with two or three other caps for now..
I do need to make my Power Supply (Battery Eliminator) for it, so that is on top of the list..
So, that alot has already been done, untill I can get the proper tube.. And then power it up for the first time, since I have had it..
THANK YOU Marty

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

using 12AU7 on 34 - by marty - 06-30-2013, 09:46 AM

RE: using 12AU7 on 34 - by codefox1 - 06-30-2013, 10:12 AM

RE: using 12AU7 on 34 - by marty - 06-30-2013, 03:29 PM

RE: using 12AU7 on 34 - by codefox1 - 06-30-2013, 03:45 PM

RE: using 12AU7 on 34 - by morzh - 06-30-2013, 03:46 PM

RE: using 12AU7 on 34 - by marty - 06-30-2013, 03:57 PM

RE: using 12AU7 on 34 - by morzh - 06-30-2013, 04:08 PM

RE: using 12AU7 on 34 - by marty - 06-30-2013, 04:46 PM

RE: using 12AU7 on 34 - by morzh - 06-30-2013, 06:00 PM

RE: using 12AU7 on 34 - by marty - 06-30-2013, 09:03 PM

RE: using 12AU7 on 34 - by morzh - 06-30-2013, 09:17 PM

RE: using 12AU7 on 34 - by Mondial - 06-30-2013, 09:28 PM

RE: using 12AU7 on 34 - by marty - 06-30-2013, 09:51 PM

RE: using 12AU7 on 34 - by Mondial - 06-30-2013, 10:13 PM

RE: using 12AU7 on 34 - by marty - 06-30-2013, 10:39 PM

RE: using 12AU7 on 34 - by morzh - 06-30-2013, 10:53 PM

RE: using 12AU7 on 34 - by marty - 07-06-2013, 09:54 AM

RE: using 12AU7 on 34 - by codefox1 - 07-06-2013, 12:04 PM

RE: using 12AU7 on 34 - by marty - 07-06-2013, 04:47 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me