1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Output Trans on 34
marty
Member
***
Posts: 240
Threads: 27
Joined: Jun 2013
City: Boulder, Colorado
#5

07-14-2013, 10:53 PM
Hi All;
Thanks Morzh, I just wanted to make sure before I did anything, that I wouldn't make anything worse than it already is..
So, yes, I can test the Transformer with my 4" PM Speaker attached to it, and see what comes out of it..
I am not going to use the Speaker that came with it, as it is in too bad a shape, the voice coil works, but the cone is torn and in very bad shape and is not attached to the Speaker frame at all..
I am going to use my Signal generator, which also has a 400 hertz Audio tone output on it and see if it is enough to make the Speaker Hum, then using the Output Transformer and then the number 19 Tube and then the Input Transformer and then the number 30 Tube driving it..
Working back ward from Speaker to antenna making sure that each section works before going any further..
Hopefully the Signal generator has enough oomph to work the Transformer to the Speaker, before wiring in the 19 Tube and so on..
THANK YOU for Your Help.. Marty
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Output Trans on 34 - by marty - 07-14-2013, 10:08 AM
RE: Output Trans on 34 - by morzh - 07-14-2013, 10:43 AM
RE: Output Trans on 34 - by marty - 07-14-2013, 03:40 PM
RE: Output Trans on 34 - by morzh - 07-14-2013, 08:07 PM
RE: Output Trans on 34 - by marty - 07-14-2013, 10:53 PM
RE: Output Trans on 34 - by morzh - 07-14-2013, 11:04 PM
RE: Output Trans on 34 - by marty - 07-14-2013, 11:09 PM
RE: Output Trans on 34 - by marty - 07-15-2013, 11:30 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Hi OSanders, Look carefully at the band switch. Turn it slowly and "wiggle" it around the desired band. ...MrFixr55 — 12:33 AM
5U4 vs 5Z4 tubes
I think that RCA and GE introduced metal tubes in the USA in 1936.  I don't know if they were being made by RCA, GE or b...MrFixr55 — 11:20 PM
Philco 42-345 Restoration/Repair
Vlad95, Thank you for the stringing guides and wow there are so manyosanders0311 — 06:01 PM
5U4 vs 5Z4 tubes
A pre war Hallicrafters, and an early one too, very nice! 1936 is pretty early for metal tubes too, which would explain ...Arran — 05:58 PM
Philco 42-345 Restoration/Repair
Thanks Rod, "When you hear the background hiss and no station it usually indicates that the oscillator quit" ...osanders0311 — 05:52 PM
Philco 42-345 Restoration/Repair
RodB :beerchug:Vlad95 — 10:22 AM
Philco 42-345 Restoration/Repair
Vlad, you nailed it. Swiss and German roots.RodB — 09:54 AM
5U4 vs 5Z4 tubes
Well this is a Hallicrafters SX/9 circa 1936. No real issues so far although I dodged a real bullet with a cap that was...bridkarl — 07:59 AM
5U4 vs 5Z4 tubes
The pinout is the same but the 5U4 has a 3 amp filament, verses 2 amps or less on the 5Z4. I think that the pinout of a ...Arran — 12:04 AM
Philco 42-345 Restoration/Repair
By the way. osanders0311 Take a look here: Dial cord stringing Guides May be here you can fount correct string settin...Vlad95 — 11:15 PM

[-]
Who's Online
There are currently 1221 online users. [Complete List]
» 1 Member(s) | 1220 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration