Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 38-40T
#9

Warren, thanks for the warning. I knew about the importance, but not just anybody would have!

Restuffing, now that's an idea I would not have thought of.... Thanks PuhPow and Mondial. Also, thanks for the schematic, I already found that one as well. It should be sufficient.

I'm not personally worried about the original appearance underneath. I'm thinking that staying true to the design is important (i.e., don't duct tape in an iPod). But, if somebody follows me in 20 years and sees the work, they will know somebody else was through. (hopefully they won't shake their head and swear at what they find...)

I expect that I'll have what I need to get started on the weekend, but I have some obligations that may prevent that. I'll keep ya'll posted. I'll have photos when I have a link to a photo site.


Messages In This Thread
Philco 38-40T - by dustyshoes - 08-12-2013, 12:11 AM
RE: Philco 38-40T - by Arran - 08-12-2013, 05:45 AM
RE: Philco 38-40T - by Jamie - 08-12-2013, 07:41 AM
RE: Philco 38-40T - by dustyshoes - 08-12-2013, 10:28 AM
RE: Philco 38-40T - by dustyshoes - 08-12-2013, 11:29 PM
RE: Philco 38-40T - by Warren - 08-12-2013, 11:48 PM
RE: Philco 38-40T - by Jamie - 08-13-2013, 04:51 AM
RE: Philco 38-40T - by Mondial - 08-13-2013, 09:22 AM
RE: Philco 38-40T - by dustyshoes - 08-13-2013, 11:54 AM
RE: Philco 38-40T - by dustyshoes - 08-19-2013, 08:27 PM
RE: Philco 38-40T - by dustyshoes - 08-28-2013, 09:27 PM
RE: Philco 38-40T - by dustyshoes - 08-28-2013, 09:31 PM
RE: Philco 38-40T - by dustyshoes - 09-20-2013, 08:45 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>