Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Need help with Philco 620
#15

Hi All;
One possibility, but not the only source of Hum.. Is if the Power Transformer circuit, is not filtering good enough, or is wired wrong.. Possibly, too low of a Capasitance, in the circuit, bad choke or not wired in, when subbing resistors for choke the Capasitance is not big enough to overcome the resulting waves in the AC turned to DC..
My Philco 34 power supply for the 137 Volt supply had too low of a capacitor to do its job and so I had lots of hum.. I ordered some new ones in ( got them in yesterday ) and it took care of my Hum problem..
THANK YOU Marty


Messages In This Thread
Need help with Philco 620 - by Jamie - 08-09-2013, 03:16 PM
RE: Need help with Philco 620 - by marty - 08-09-2013, 05:44 PM
RE: Need help with Philco 620 - by Phlogiston - 08-09-2013, 06:28 PM
RE: Need help with Philco 620 - by morzh - 08-09-2013, 06:50 PM
RE: Need help with Philco 620 - by Jamie - 08-09-2013, 07:28 PM
RE: Need help with Philco 620 - by Phlogiston - 08-09-2013, 08:13 PM
RE: Need help with Philco 620 - by Jamie - 08-09-2013, 08:32 PM
RE: Need help with Philco 620 - by Phlogiston - 08-09-2013, 08:48 PM
RE: Need help with Philco 620 - by Jamie - 08-09-2013, 09:12 PM
RE: Need help with Philco 620 - by Jamie - 08-14-2013, 09:44 AM
RE: Need help with Philco 620 - by Phlogiston - 08-14-2013, 10:02 AM
RE: Need help with Philco 620 - by Jamie - 08-14-2013, 12:22 PM
RE: Need help with Philco 620 - by Arran - 08-14-2013, 07:57 PM
RE: Need help with Philco 620 - by Jamie - 08-15-2013, 08:47 AM
RE: Need help with Philco 620 - by marty - 08-15-2013, 02:37 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently no members online.

>