Philco 90 Help Needed

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 90 Help Needed

Scott Fletcher
Junior Member

Posts: 10
Threads: 1
Joined: Aug 2013
City: Dowagiac, Mi.

08-17-2013, 04:54 PM

I have an early Philco 90 I am restoring. It has two 45 output tubes and I have a bad output transformer(chicago jefferson 2766J). Could some one please advise me as to where I could find a replacement for this. I have looked at several of the parts sites mentioned on this forum and in the forum posts and can't find any reference or source for this. It looks like Hammond doesn't make a suitable replacement.
Another question I have concerns the Philco 90 schematic which I downloaded from this web site. By the #47 part baloon just above the 27 oscillator tube is a capacitor connected to ground. No value is listed for this cap. What is it and where is it located? I would greatly appreciate any help anyone could provide. Thanks.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Philco 90 Help Needed - by Scott Fletcher - 08-17-2013, 04:54 PM

RE: Philco 90 Help Needed - by morzh - 08-17-2013, 10:29 PM

RE: Philco 90 Help Needed - by Ron Ramirez - 08-18-2013, 09:13 AM

RE: Philco 90 Help Needed - by Chuck Schwark - 08-20-2013, 09:56 AM

RE: Philco 90 Help Needed - by morzh - 08-20-2013, 02:59 PM

RE: Philco 90 Help Needed - by Scott Fletcher - 08-20-2013, 04:26 PM

RE: Philco 90 Help Needed - by morzh - 08-20-2013, 09:40 PM

RE: Philco 90 Help Needed - by marty - 08-20-2013, 09:54 PM

RE: Philco 90 Help Needed - by Mondial - 08-20-2013, 11:27 PM

RE: Philco 90 Help Needed - by Scott Fletcher - 08-21-2013, 04:30 PM

RE: Philco 90 Help Needed - by Mondial - 08-21-2013, 08:33 PM

RE: Philco 90 Help Needed - by Scott Fletcher - 08-24-2013, 05:08 PM

RE: Philco 90 Help Needed - by Scott Fletcher - 09-06-2013, 04:33 PM

RE: Philco 90 Help Needed - by BrendaAnnD - 09-06-2013, 04:42 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco Model 38-7: what caps & resistors do fail typically?
Since you stated earlier, you have a console 38-7XX. They also had a 38-7T (table), and 38-7CS (chairside). A very nic...GarySP — 01:18 PM
Part numbers to model cross
That I wouldn't know, but sometimes the radio document itself shows one, same as the capacitor cans' etc pinouts.morzh — 12:46 PM
Part numbers to model cross
Thank you morzh, that is exactly what I was looking for. Now , is there some where that shows pinouts for Philco power ...Jim Dutridge — 11:37 AM
Restoration of the Canadian General Electric A-87
Thanks for your help Michael. In fact, this video is only an intermediate result. Later I had to apply another tinting l...RadioSvit — 09:01 AM
Restoration of the Canadian General Electric A-87
Great job on the cabinet. PS. In the US notation, "kenotron" refers to specific type of tubes; we call re...morzh — 08:24 AM
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. Search f...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me