Poss. OSC Problems Philco 34

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Poss. OSC Problems Philco 34

marty
Member

Posts: 240
Threads: 27
Joined: Jun 2013
City: Boulder, Colorado

08-17-2013, 09:43 PM

Hi All;
I think I have found two problems, one major.. The minor problem was a possible short on the Lead from the Grid Cap of the 1C6 to the top of the tuner may have been shorted to the base of the tuning Capacitor.. Or it was some of the time..
The other major problem was I had on the 1C6 G1 and G2 switched, Thank You Arran.. I might not have found it otherwise.. I went to a Philco 623 and found the Pinout for the 1C6, from the bottom view , with voltages, and that is what led to me finding the problem.. My soldering Iron is warming up while I write this, and after I close this, I will fix it..
THANK YOU Marty

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Poss. OSC Problems Philco 34 - by marty - 08-16-2013, 12:08 AM

RE: Poss. OSC Problems Philco 34 - by BrendaAnnD - 08-16-2013, 02:10 AM

RE: Poss. OSC Problems Philco 34 - by marty - 08-16-2013, 10:16 AM

RE: Poss. OSC Problems Philco 34 - by Arran - 08-16-2013, 07:42 PM

RE: Poss. OSC Problems Philco 34 - by marty - 08-16-2013, 08:37 PM

RE: Poss. OSC Problems Philco 34 - by marty - 08-17-2013, 09:43 PM

RE: Poss. OSC Problems Philco 34 - by marty - 08-17-2013, 10:23 PM

RE: Poss. OSC Problems Philco 34 - by marty - 08-19-2013, 02:48 PM

RE: Poss. OSC Problems Philco 34 - by marty - 08-19-2013, 04:13 PM

RE: Poss. OSC Problems Philco 34 - by marty - 08-26-2013, 01:38 PM

RE: Poss. OSC Problems Philco 34 - by marty - 08-26-2013, 03:12 PM

RE: Poss. OSC Problems Philco 34 - by marty - 08-31-2013, 07:02 PM

RE: Poss. OSC Problems Philco 34 - by marty - 09-02-2013, 10:34 AM

RE: Poss. OSC Problems Philco 34 - by marty - 09-02-2013, 02:28 PM

RE: Poss. OSC Problems Philco 34 - by marty - 09-02-2013, 09:34 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online

There are currently 746 online users. [Complete List]
» 1 Member(s) | 745 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me