Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Need Help Reading a Schematic
#4

Also keep in mind that the #68 cap has its (+) - PLUS terminal to the chassis and NOT the (-) Minus. Many people make that mistake.

It also helps if you do not use the word "ground to somewhere else". You van ONLY ground to the Ground (or you can call it "chassis"). Otherwise it is not grounding. But of you call it "grounding" it kinda sets your mind to try to connect it to GND whereas it might not be connected there at all. Using right terminology disciplines the mind and eventually prevents you from connecting things to where they do not belong. Like to the Chassis all the time.


Messages In This Thread
Need Help Reading a Schematic - by Jamie - 08-17-2013, 07:25 AM
RE: Need Help Reading a Schematic - by Jamie - 08-17-2013, 11:00 PM
RE: Need Help Reading a Schematic - by morzh - 08-17-2013, 11:14 PM
RE: Need Help Reading a Schematic - by Jamie - 08-17-2013, 11:24 PM
RE: Need Help Reading a Schematic - by codefox1 - 08-18-2013, 10:57 AM
RE: Need Help Reading a Schematic - by morzh - 08-18-2013, 11:05 AM
RE: Need Help Reading a Schematic - by Jamie - 08-18-2013, 12:13 PM
RE: Need Help Reading a Schematic - by Jamie - 08-18-2013, 06:53 PM
RE: Need Help Reading a Schematic - by morzh - 08-18-2013, 08:21 PM
RE: Need Help Reading a Schematic - by Arran - 08-18-2013, 10:16 PM
RE: Need Help Reading a Schematic - by Jamie - 08-19-2013, 08:18 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently 948 online users. [Complete List]
» 2 Member(s) | 946 Guest(s)
AvatarAvatar

>