Philco 96 Whooped boy

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 96 Whooped boy

49Stude63
Member

Posts: 225
Threads: 14
Joined: Oct 2005
City: Grand Blanc, Michigan

11-20-2005, 04:05 PM

I have to take some more pictures I have glued all the loose joints and veneer which has been time consuming because there was so many loose sections and I only have so many clamps. It appears to be shaping up good but I think in the end I may sand the top and use some filler to fix the bad spots and then use black lacquer on the top. I know some models had black lacquer tops, I'm don't think the 96 highboy is one but hopefully it won't look too out of place.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Philco 96 Whooped boy - by 49Stude63 - 10-20-2005, 10:28 PM

[No subject] - by Chuck Schwark - 10-20-2005, 10:49 PM

[No subject] - by Jerry Huelsbeck - 10-20-2005, 10:54 PM

[No subject] - by 49Stude63 - 10-20-2005, 11:04 PM

[No subject] - by Ron Ramirez - 10-20-2005, 11:27 PM

[No subject] - by 49Stude63 - 10-21-2005, 11:31 PM

[No subject] - by Chuck Schwark - 10-21-2005, 11:42 PM

[No subject] - by 49Stude63 - 11-20-2005, 04:05 PM

[No subject] - by Ron Ramirez - 11-27-2005, 10:13 PM

[No subject] - by Ron Ramirez - 11-29-2005, 06:54 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

Who's Online

There are currently 2137 online users. [Complete List]
» 1 Member(s) | 2136 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me