Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

New Grille Cloth Available
#4

Kenny's "whiskey rayon" pattern, fourth from the top in the photos above, is as close as we can get to the old 70/90 cloth right now. This pattern was also used in most 1932 and 1933 Philco cathedral models; the 80B and 81B being exceptions.

--
Ron Ramirez
Ferdinand IN


Messages In This Thread
New Grille Cloth Available - by Ron Ramirez - 09-01-2013, 09:04 AM
RE: New Grille Cloth Available - by Eliot Ness - 09-02-2013, 08:50 PM
RE: New Grille Cloth Available - by Sean - 09-03-2013, 09:14 AM
RE: New Grille Cloth Available - by Ron Ramirez - 09-03-2013, 09:17 AM
RE: New Grille Cloth Available - by BDM - 09-07-2013, 01:16 PM
RE: New Grille Cloth Available - by TA Forbes - 09-07-2013, 06:24 PM
RE: New Grille Cloth Available - by TA Forbes - 09-07-2013, 06:27 PM
RE: New Grille Cloth Available - by morzh - 09-07-2013, 09:28 PM
RE: New Grille Cloth Available - by Ron Ramirez - 09-07-2013, 09:38 PM
RE: New Grille Cloth Available - by morzh - 09-07-2013, 11:51 PM
RE: New Grille Cloth Available - by TA Forbes - 09-08-2013, 11:03 AM
RE: New Grille Cloth Available - by morzh - 09-08-2013, 12:45 PM
RE: New Grille Cloth Available - by Geoff - 09-09-2013, 04:03 PM
RE: New Grille Cloth Available - by Ron Ramirez - 09-09-2013, 04:42 PM
RE: New Grille Cloth Available - by Eliot Ness - 09-09-2013, 06:18 PM
RE: New Grille Cloth Available - by hunter2115 - 09-10-2013, 02:38 PM
RE: New Grille Cloth Available - by TA Forbes - 09-10-2013, 09:19 PM
RE: New Grille Cloth Available - by y2kbruce - 09-11-2013, 03:02 PM
RE: New Grille Cloth Available - by Chicago Jimmy - 09-11-2013, 06:05 PM
RE: New Grille Cloth Available - by fossilexpress - 09-11-2013, 09:25 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 728 online users. [Complete List]
» 1 Member(s) | 727 Guest(s)
Avatar

>